Table of Contents
Advertisement
Quick Links
1. Safety Precautions and Warnings ............................ 1
2. Location of Data Link Connector (DLC) ................... 2
3. Using the EPB Service Tool ...................................... 3
3.1 Tool Description ............................................... 3
3.2 Specifications ................................................... 4
3.3 Accessories ...................................................... 4
3.4 Navigation Characters ...................................... 4
3.5 Vehicle Power ................................................... 4
3.6 Product Setup ................................................... 5
3.7 Vehicle Coverage .............................................. 7
4. Diagnostics ................................................................. 7
4.1 Diagnose EPB on Audi A8 and Other ............. 8
4.2 Diagnose Mercedes SBC ............................... 13
5. Updates ..................................................................... 22
6. Warranty and Service .............................................. 22
6.1 Limited One Year Warranty ............................ 22
6.2 Service Procedures ........................................ 23
Table of Contents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Autel AutoLink EBT 210
Summary of Contents for Autel AutoLink EBT 210
-
Page 1: Table Of Contents
Table of Contents 1. Safety Precautions and Warnings ......1 2. Location of Data Link Connector (DLC) ....2 3. Using the EPB Service Tool ........3 3.1 Tool Description ..........3 3.2 Specifications ........... 4 3.3 Accessories ............4 3.4 Navigation Characters ........ -
Page 2: Safety Precautions And Warnings
1. Safety Precautions and Warnings To prevent personal injury or damage to vehicles and/or the brake tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle: Always perform automotive testing in a safe environment. ... -
Page 3: Location Of Data Link Connector (Dlc)
2. Location of Data Link Connector (DLC) The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-pin connector where diagnostic brake tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. -
Page 4: Using The Epb Service Tool
3. Using the EBT 210 Service Tool 3.1 Tool Description OBD II CABLE -- Connects the brake tool to the vehicle’s Data Link Connector (DLC). LCD DISPLAY -- Indicates test results. UP SCROLL BUTTON -- Moves up through menu and submenu items in menu mode. -
Page 5: Specifications
3.2 Specifications Display: Backlit, 128 x 64 pixel display Operating Temperature: 0 to 60°C (32 to 140 F°) Storage Temperature: -20 to 70°C (-4 to 158 F°) Power: 8 to 18 Volts provided via vehicle battery Dimensions: Length Width Height 110.3 mm (4.34 "... -
Page 6: Product Setup
3.6 Product Setup The brake tool allows you to make the following adjustments and settings: Language: Selects desired language. The device supports English by default. Contrast: Adjusts the contrast of the LCD display. Tool Information: Provides important information about the device, such as S/N, software version, hardware version and trouble code library version. - Page 7 Use UP/DOWN button to select the desired language and press Y button to save your selection and return to previous menu. …………………Language…………………. English ► Contrast Adjustment From System Setup menu, use UP/DOWN button to select Contrast, and press Y button. …………….System Setup…………...
-
Page 8: Vehicle Coverage
…………….System Setup………… ……. 1) Language 2) Contrast ►3) Tool Information View tool information on the screen. Tool Information ……. Serial No. : xxxxxxxx Burn Date: 11/12/08 S/W Ver : V1.00 H/W Ver : V1.01 LIB Ver V1.00 Press any key to return. 3.7 Vehicle Coverage The AutoLink EBT210 Electronic Parking Brake Service Tool... -
Page 9: Diagnose Epb On Audi A8 And Other
Turn the ignition on. Press Y button from home screen to enter Diagnostic Menu. …… AUDI …………… … ►1) Audi A8 2) Other Audi 4.1 Diagnose EPB on Audi A8/A6 & Passat The AutoLink EBT210 is able to open/close brake pads, read/clear EPB trouble codes on vehicles that are equipped with EPB system. - Page 10 Select For Pad Change ..Guided Function ..► 1) For Pad Change 2) For Repair Perform the following procedure ..Test Condition ► 1) Turn Ignition On 2) Release EPB 3) Shift to P Position [Y]=Continue [N]=EXIT If a trouble Code is found, click Y to continue. It will be cleared in a later step.
- Page 11 Continue by pressing [Y] ..Replace Brake Pads Installation of the rear brake pads by Audi service manual. [Y]=Continue Only close once brake pads are correctly replaced..Close Brake Pads Make sure brake pads are replaced OK. Then Close it. [Y]=Continue Wait for brakes to close.
- Page 12 ..Enter thickness [UP ARROW]/[DOWN ARROW] [Y]=Confirm 12) The new brake pad thickness will be stored..Store Thickness The new brake pad thickness is being stored. -Please wait- 13) Follow the steps for re-calibration. Use down arrows to see all of the requirements’...
- Page 13 …… \ Re-calibration … … 4) Lock Steering Wheel (may lock automatically) [Y] = Continue …… \ Re-calibration … … The re-calibration will be carried out. The EPB now open and closes audible. …… \ Re-calibration … … Wait until this procedure is completed [Y]=Continue 14) This completes the re-calibration.
-
Page 14: Diagnose Mercedes Sbc
…… \ End of Test … … The DTC memory has been erased successfully. END OF TEST. 4.2 Diagnose Mercedes SBC The AutoLink EBT210 is able to deactivate/activate SBC functions, read/clear SBC trouble codes, and retrieve ECU information on Mercedes vehicles that are equipped with SBC system. - Page 15 Verify that the ignition is ON; Check if the brake tool’s OBD II connector is securely connected to the vehicle’s DLC; Turn the ignition off and turn it back on 10s later. If the “LINK ERROR!” message does not go away, then there might be problems for the brake tool to communicate with the vehicle.
- Page 16 C2117 stored Control unit A7/3n1 (SBC control unit), Internal fault The sequence of the DTCs, total number of codes detected and type of codes (stored or current) will be observed on the display. When more than one DTC is found, use UP/DOWN button, as necessary, until all the codes have been shown up.
- Page 17 .... Select Function ..1) Read Codes ►2) Erase Codes 3) Deactivate Brake 4) Activate Brake A warning message comes up asking for your confirmation....Erase Codes....Erase trouble codes! Are you sure? f you do not wish to proceed to erase the codes, press N button or use UP/DOWN button to select NO and then press Y button to exit.
- Page 18 To open the brake pads, use UP/DOWN button to select Deactivate Brake from Select Function menu and press Y button..Select Function ..1) Read Codes 2) Erase Codes ► 3) Deactivate Brake 4) Activate Brake Deactivation of Brakes Test Sequence ..
- Page 19 ..Deactivate Brake..Reservoir charge pump Startup is blocked. [Y]=Continue ………. . Deactivate Brake …………. Deactivating… -Please Wait- Wait a few minutes while the tool is deactivating. When the brakes are deactivated successfully, following screen shows: ..Deactivate Brake ..
- Page 20 close brake pads after finishing maintenance/service work on the brakes, use UP/DOWN button to select Activate Brake from Select Function menu and press Y button. Perform the following procedure to activate the brakes..Select Function ..1) Read Codes 2) Erase Codes 3) Deactivate Brake ►4) Activate Brake...
- Page 21 ………. . Pressure Sensor …………. Left Front: 67.9bar Right Front: 68.9bar Left Rear: 68.1bar Right Rear: 68.6bar Requirements: >=50bar Press [Y] to continue ………. . Activate Brake …………. Activating… -Please Wait- ………. . Activate Brake …………. Turn ignition off for about 3 seconds Then, turn ignition on.
- Page 22 Wait a few minutes while the device is activating the brakes. When they are activated successfully, following screen shows: …………… Activate Brake …….. . Activation Done! Press any key to con. If the tool fails to close the brakes, an “Activation Failed! Press any key to con.”...
-
Page 23: Updates
6. Warranty and Service 6.1 Limited One Year Warranty Autel.US warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one (1) year from the date of the original purchase, subject to the... -
Page 24: Service Procedures
Manufacturer’s Service Center. 3) Autel.US shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the brake tool. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Need help?
Do you have a question about the AutoLink EBT 210 and is the answer not in the manual?
Questions and answers