Makita DHS782 Instruction Manual page 13

$ EDWWHU\ VKRUW FDQ FDXVH D ODUJH FXUUHQW ÀRZ RYHU-
heating, possible burns and even a breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
RXW 7KH EDWWHU\ FDUWULGJH FDQ H[SORGH LQ D ¿UH
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
)RU FRPPHUFLDO WUDQVSRUWV HJ E\ WKLUG SDUWLHV
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
LQJ DQ H[SHUW IRU KD]DUGRXV PDWHULDO LV UHTXLUHG
3OHDVH DOVR REVHUYH SRVVLEO\ PRUH GHWDLOHG
national regulations.
Tape or mask off open contacts and pack up the
EDWWHU\ LQ VXFK D PDQQHU WKDW LW FDQQRW PRYH
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
12. Use the batteries only with the products
VSHFL¿HG E\ 0DNLWD Installing the batteries to
QRQFRPSOLDQW SURGXFWV PD\ UHVXOW LQ D ¿UH H[FHV-
VLYH KHDW H[SORVLRQ RU OHDN RI HOHFWURO\WH
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
KDYH EHHQ DOWHUHG PD\ UHVXOW LQ WKH EDWWHU\ EXUVWLQJ
FDXVLQJ ¿UHV SHUVRQDO LQMXU\ DQG GDPDJH ,W ZLOO
DOVR YRLG WKH 0DNLWD ZDUUDQW\ IRU WKH 0DNLWD WRRO DQG
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
Important safety instructions for
wireless unit
1. Do not disassemble or tamper with the wire-
less unit.
2. Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
3. Use the wireless unit only with Makita tools.
4. Do not expose the wireless unit to rain or wet
conditions.
5. Do not use the wireless unit in places where
the temperature exceeds 50°C (122°F).
6. Do not operate the wireless unit in places
where medical instruments, such as heart
pace makers are nearby.
7. Do not operate the wireless unit in places where
automated devices are nearby. If operated, auto-
PDWHG GHYLFHV PD\ GHYHORS PDOIXQFWLRQ RU HUURU
8. Do not operate the wireless unit in places under
high temperature or places where static electric-
ity or electrical noise could be generated.
9. The wireless unit can produce electromagnetic
¿HOGV (0) EXW WKH\ DUH QRW KDUPIXO WR WKH XVHU
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct
direction.
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when
operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
'RLQJ VR PD\ FDXVH D PDOIXQFWLRQ RI WKH ZLUHOHVV
unit.
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. :DWHU GXVW DQG GLUW FRPH LQWR WKH VORW PD\
cause malfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
13 ENGLISH