Personal Safety - DeWalt XR Li-Ion Flexvolt DCG200 Original Instructions Manual

Wireless Tool Control (Fig. A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with the
wall chaser.
Your wall chaser is equipped with a Wireless Tool Control
transmitter which allows your wall chaser to be wirelessly
paired with another Wireless Tool Control device, such as a
dust extractor.
To pair your wall chaser using Wireless Tool Control, press and
hold the trigger switch 1 on the wall chaser and the Wireless
Tool Control pairing button on the seperate device. An LED on
the seperate device will let you know when your wall chaser has
been successfully paired.
Trigger Switch and Lock-off Lever (Fig. F)
1. To turn the tool on, push the lock-off lever
back of the tool, then depress the trigger switch
will run while the switch is depressed.
2. Turn the tool off by releasing the trigger switch.

WARNING: Hold the auxiliary handle and body of the
tool firmly to maintain control of the tool at start up and
during use and until the diamond blades stop rotating.
Make sure the diamond blades have come to a complete
stop be fore laying the tool down.

WARNING: Allow the tool to reach full speed before
touching tool to the work surface. Remove the tool from
the work surface before turning the tool off.
Spindle Lock (Fig. G)
The spindle lock button 3 is provided to prevent the spindle
from rotating when installing or removing diamond blades.
Operate the spindle lock only when the tool is turned off,
unplugged from the power supply, and has come to a
complete stop.
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached diamond
blades may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate the
spindle further.
Dust Extraction (Fig. A, H)

WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dust mask.

WARNING: ALWAYS use a dust class M vacuum extractor
designed in compliance with the applicable directives
regarding dust emission when cutting hazardous dust.
The dust extraction port 4 allows you to connect the tool to
an external dust extractor, either using the AirLock system, or a
standard 35 mm dust extractor fitment. The dust extraction port
is adjustable through 180 degrees.
The AirLock connector 22 connects directly to D
compatable tools and extractors.
1. Ensure the collar on the AirLock connector is in the unlock
position. (Refer to Figure H) Align notches
AirLock connector as shown for unlock and lock positions.
2. Push the AirLock connector onto the dust extraction port.
3. Rotate the collar to the locked position.
nOTE: The ball bearings inside collar lock into slot and
secure the connection.The power tool is now securely
connected to the dust extractor.

Personal Safety

1. No children or pregnant women should enter the work area
where the paint sanding or wire brushing is being done
until all clean up is completed.
2. A dust mask or respirator should be worn by all persons
entering the work area. The filter should be replaced daily or
whenever the wearer has difficulty breathing.
2 toward the
nOTE: Only those dust masks suitable for working with lead
. The tool
1
paint dust and fumes should be used. Ordinary painting
masks do not offer this protection. See your local hardware
dealer for the proper approved mask.
3. NO EATING, DRINKING or SMOKING should be done in the
work area to prevent ingesting contaminated paint particles.
Workers should wash and clean up BEFORE eating, drinking
or smoking. Articles of food, drink, or smoking should not be
left in the work area where dust would settle on them.
Cleaning and Disposal
1. Plastic drop cloths should be gathered up and disposed
of along with any dust chips or other removal debris. They
should be placed in sealed refuse receptacles and disposed
of through regular waste pick-up procedures.
During clean up, children and pregnant women should be
kept away from the immediate work area.
2. All toys, washable furniture and utensils used by children
should be washed thoroughly before being used again.
Chasing
1. Always use dust extraction.
2. Set the correct depth and width.
3
3. Position yourself so that the open-underside of the guard is
facing away from you.
4. Ensure the base of the guard is always flat to the surface to
allow for efficient dust extraction.
5. Allow the tool to reach full speed before touching the tool
to the work surface.
6. Apply minimum pressure to the work surface, allowing the
tool to operate at high speed. Cutting rate is greatest when
the tool operates at high speed.
7. When using on vertical surfaces always start at the top
and pull the tool down, following the direction arrows as
indicated on the shoe.
8. Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
WALT
e
the angle will cause the diamond blades to bend and
may cause breakage. Diamond blades are not designed to
withstand side pressures caused by bending.
English
on collar and
23
13