J&M GC24t-1 Operator's Manual page 43

Roll Tarp Assembly
# Description
1 Front End Cap Plate, Grain Cart 140"
2 Tarp Nylon Riser
3 Front End Cap Arch, Grain Cart 140"
4 M6 x 1.0 x 20MM Grade 8.8 Hex Bolt
5 M6 x 1.0 Gr8.8 YZ SF Hex Nut
6 M6 x 1.0 x 20MM Grade 8.8 Hex Bolt
7 Rear End Cap Arch, Grain Cart 140"
8 3/8"-16 Gr5 Z J-Bolt
9 3/8"-16 Gr5 Z Centerlock Hex Nut
10 Rear End Cap Plate, Grain Cart 137-1/4"
11 1/4" ID, 3/4" OD Z Flat Washer
12 Tarp Standoff
13 1/4" x 1-1/2" Self Tapping Screw
14 End Cap Prop 13" - Upper
15 M10 x 1.5 x 25MM Gr8.8 YZ Hex Bolt
16 M10 x 1.50 Gr8.8 YZ SF Hex Nut
17 Endcap Prop - Lower 19" (ABS-2)
18 M10 x 1.5 x 50MM Gr8.8 YZ Hex Bolt
19 M6 x 1.0 Gr8.8 YZ Nylon Locking Hex Nut
20 M10 x 1.50 Gr8.8 YZ SF Hex Nut
21 M6 x 1.00 x 65MM Hex Bolt
22 M12-1.75 Gr8.8 YZ Nylon Locking Hex Nut
23 Crank Holder (zinc plated)(CH-1)
24 Roll Tarp - Handle Hanger Rubber Flap
25 1/2" ID 1-3/8" OD Z Flat Washer
26 M12 x 1.75 x 35MM Gr8.8 YZ Hex Bolt
27 1/4" x 2" x 29" Adj. Bar for Crank Handle Holder JM0000164
28 3/16" Cable x 198" Long
29 1-1/8" x 198" Square Roll Tube Weldment
30 15'8" x 13'6'" Tarp w/ 10 Rivets (875, GC24t-1)
31 1" x 192" Square Tie-Down Tube for Roll Tarp
32 Tightening Lip x 192"
33 137" Arched Tarp Bows (Regular)
34 9-1/2' Crank w/ Splined U-Joint
35 S-Cap Yellow - 1.062 ID x 1.5 x 0.065
36 M10-1.5 x 50" Gr8.8 YZ Hex Bolt
37 Tarp Stop Bracket (TSB-1)
38 1/8" Cable Clamp
39 Universal Joint - Roll Tarp
Part. No.
JM0000194
JM0000196
JM0000195
JM0002120
JM0002156
JM0002120
JM0000172
JM0001519
JM0001512
JM0000169
JM0003090
JM0001889
JM0001571
JM0021404
JM0031355
JM0002154
JM0000179
JM0001486
JM0002167
JM0002154
JM0002121
JM0002163
JM0002967
JM0002551
JM0003082
JM0020955
JM0022194
JM0022191
JM0018184
JM0000188
JM0000155
JM0000157
JM0000185
JM0018963
JM0001486
JM0000187
JM0001514
JM0001517
43