Control Panel; Setting The Clock; Brewing Coffee; Temperature Control For Warming Plate - Black & Decker CMD3400MB Use And Care Book Manual

W TER FILTER REPL CEMENT:
1. Press latch on filter holder to open (see illustration C).
2. Dispose of old carbon filter.
3. Remove new carbon filter from packing material.
4. Place new carbon filter inside filter holder.
5. Close the filter holder tightly until it snaps into place (see illustration D).
6. Place filter holder inside the water reservoir and insert it into the recess at the
bottom right hand corner (see illustration E).
Note: Replace carbon filter every 60 brewing cycles or every 2 months after
removing it from the sealed package. (Call the 800 number on the front cover for
replacements)

SETTING THE CLOCK:

1. Plug appliance into standard electrical outlet.
12:00
2. The digital clock display flashes 12:00 .M. (F).
AUTO
POWER
AM
3. To change the time: Press Hour button until the correct
MILD
REGULAR
STRONG
BREW
PROG
STRENGTH
time appears on the display. Repeat with the Min button.
TIP: Holding the button down makes the hours and
HOUR TEMP MIN
WARMING PLATE
minutes change rapidly after a short delay; tapping changes
F
the time in 1 minute increments.
NOTE: If the unit is unplugged or power is interrupted even momentarily,
the time will need to be reset.

BREWING COFFEE:

1. Plug cord into a standard electrical outlet.
2. Open water reservoir cover.
3. Fill carafe with desired amount of cold tap water using
the water markings on the carafe; pour into water
reservoir (G).
G
Note: Do not exceed the 12-cup maximum level.
4. Close water reservoir cover securely.
5. Press brew basket compartment release button to open.
6. Place 8 to 12 cup basket style paper filter into the
removable brew basket (H).
7. dd desired amount of ground coffee.
8. Close brew basket compartment securely.
H
9. Place empty carafe on the warming plate.
AUTO
10. Select the brew strength desired by pressing the Brew
Strength button and selecting one of the 3 levels
desired (J):
MILD
• Mild
REGULAR
STRONG
• Regular
BREW
STRENGTH
J
• Strong
Note: The Brew Strength can be selected before or after brewing begins.
11. Press the Power button and brewing begins.
Note: To delay brewing see, Delayed Brewing section.
12. The unit will beep 3 times when the brewing cycle is complete.
7
13. Once the brewing cycle is complete the word Fresh
6:00
and the Fresh icon will appear on the digital
display (K).
AUTO
POWER
AM
MILD
REGULAR
FRESH
STRONG
BREW
PROG
STRENGTH
K
HOUR TEMP MIN
WARMING PLATE
14. fter 20 minutes the digital display will change
6:20
to Not Fresh and the icon will also indicate the
same (L).
AUTO
POWER
AM
NOT MILD
REGULAR
FRESH 15. Keep carafe on the warming plate between
STRONG
BREW
PROG
STRENGTH
servings to preserve the temperature of the coffee
in the carafe.
HOUR MIN
TEMP
L
WARMING PLATE
16. Once coffee grounds have cooled, press brew basket compartment release
button to open.
17. Use basket handle to remove and discard used grounds and paper filter.
Replace basket and close brew basket compartment.
18. The coffee maker automatically shuts off after 2 hours.
19. Unplug appliance when not in use.
®
SNE K- -CUP INTERRUPT FE TURE
®
The Sneak- -Cup feature allows you to pour a cup of coffee from the carafe
while the coffee is brewing. When the carafe is removed the brewing process is
paused. Simply replace the carafe on the warming plate within 30 seconds and
brewing resumes.
6:00
TEMPER TURE CONTROL FOR W RMING PL TE
AUTO
This coffeemaker has a temperature selector gauge for the warming plate on the
POWER
AM
MILD

control panel.

REGULAR
AUTO
FRESH
STRONG
BREW
PROG
1. By pressing the left or right button you can decrease or
STRENGTH
increase the temperature of the warming plate (M).
2. The bar on the LCD gives a visual display of the amount
MIN
HOUR
TEMP
of heat of the warming plate.
WARMING PLATE
Note: The temperature setting of the warming plate can be
changed at any time before, during or after brewing.
M
DEL YED BREWING:
1:00
1. Follow steps 1 through 10 under the Brewing Coffee
AUTO
section.
POWER
AM
2. Press the Prog button; the word uto flashes on the MILD
REGULAR
auto
STRONG
BREW bottom left of the display (N).
PROG
STRENGTH
3. The digital clock displays 1:00 or the previous preset
delayed start time.
N
MIN
HOUR 4. To change the time: Press the Hour button until the
TEMP
WARMING PLATE
correct time appears on the display. Repeat with the
Min button.
5. Press the Prog button again. The delayed brewing is set.
6. Press the uto button to activate the delayed brewing. The uto button lights
and the uto logo are displayed.
8