Subscribe to Our Youtube Channel
Related Manuals for ACTi R71CF-34
Summary of Contents for ACTi R71CF-34
- Page 1 Face Recognition Reader User’s Manual R71CF-31, R71CF-32, R71CF-33, R71CF-34 2019/09/23...
-
Page 2: Table Of Contents
User Management ..................22 Managing User ..................25 Other Management ................... 25 Appendix ............... 27 Tips When Collecting / Comparing Face Picture ......... 27 Position (Recommended Distance: 0.5 m) ..........27 Expression ....................28 Posture ..................... 28 Size ......................28 www.acti.com... - Page 3 User’s Manual Tips for Installation Environment ..............29 Relationship Between Wake-Up Distance and Environment ...... 30 www.acti.com...
-
Page 4: About This Manual
For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; As data controller, you are advised to collect, store, process and transfer data in www.acti.com... -
Page 5: Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. www.acti.com... - Page 6 The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info www.acti.com...
-
Page 7: Safety Instructions
Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents. www.acti.com... - Page 8 Indoor and outdoor use. If installing the device indoors, the device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. If installing the device outdoors, you should apply Silicone sealant among the cable wiring area to keep the raindrop from entering. www.acti.com...
-
Page 9: Installation And Connections
User’s Manual Thank you for purchasing ACTi products. The following documentation covers the installation and configuration of your device. NOTE: The accuracy of the analytics algorithm may be affected by different environmental factors or inappropriate installation. Please follow the procedures in this guide. ACTi will not be held liable for inaccuracies resulting from the aforesaid causes. - Page 10 4. Route the cables through the cable hole of the mounting plate, and connect to the corresponding external devices’ cables. NOTE: If installing outdoors, make sure to apply Silicone sealant on the cable wiring area to keep raindrops from entering. www.acti.com...
- Page 11 The recommended installation height 1.4 meters from the ground is a reference point. You can change it according to your actual needs. You may also install the device directly on walls without gangbox. Use the drill template to mark the screw holes to use. www.acti.com...
-
Page 12: Terminal Connection
30 m. If you use 2.0 mm cables, you should use a 12 V switched-mode power supply. And the distance between the power supply and the device should be no more than 40 m. See wiring diagram below: www.acti.com... - Page 13 User’s Manual You can also connect the device with a secure door control unit. See wiring diagram is below: NOTE: The secure door control unit should connect to an external power supply separately. www.acti.com...
-
Page 14: Device Activation
(using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your device. It is also recommended to re-set the password regularly, especially in the high security system to better protect your device. www.acti.com... -
Page 15: Basic Operation
Application Mode Settings Select the application mode for better device application. 1. In the Welcome page, select Indoor or Others from the drop-down list. 2. Tap OK to save the settings. www.acti.com... -
Page 16: Login
The Password here is the activation password. 3. Tap OK to enter the home page. NOTES: The device will be locked for 30 minutes after 5 failed password attempts. For details about setting the administrator authentication mode, see Adding User on page 22. www.acti.com... -
Page 17: General Parameters Settings
3. Tap √ to save the network parameters. Setting Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. 1. On the Communication Settings page, tap Wi-Fi to enter the Wi-Fi tab. 2. Tap to enable the Wi-Fi function. www.acti.com... - Page 18 Numbers, upper case letters, lower case letters, and special characters are allowed in the Wi-Fi password. 5. Tap OK to save the settings and go back to the Wi-Fi tab. 6. Tap to save the Wi-Fi parameters and go back to the Home page. www.acti.com...
-
Page 19: System Settings
Building No. Set the device installed Building No. Unit No. Set the device installed Unit No. Voice Prompt to disable or enable the voice prompt. Voice Volume Adjust the voice volume. The larger the value, the louder the volume. www.acti.com... - Page 20 0 refers to turning off the light. 1 refers to the darkest, and 100 refers to the brightest. Setting Time You can set the device time and the DST in this section. 1. Tap Time (Time Settings) on the Home page to enter the Time Settings page. www.acti.com...
- Page 21 DST start time, end time, and the bias time. Start Time: Set the DST start time. End Time: Set the DST end time. Bias Time: Set the DST bias time when the DST starts. 3. Tap to save the settings and go back to Home page. www.acti.com...
-
Page 22: User Management
Up to 50000 users can be added. Some models do not support the fingerprint related function. 1. On the User Management page, tap + to enter the Add User page. 2. Tap the Employee ID. field and edit the employee ID. www.acti.com... - Page 23 Tap Save to save the face picture. Or tap Try Again and adjust your face position to add the face picture again. NOTE: The maximum duration for adding a face picture is 15 seconds. You can check the remaining time for adding a face picture on the left of the page. www.acti.com...
- Page 24 When the function is enabled, the user’s card will be the duress card. When the user authenticates by swiping this duress card, the device will upload a duress card event to the client software. √ 10. Tap to save the user parameters and go back to the Home page. www.acti.com...
-
Page 25: Managing User
Managing Data On the Data Management page, you can delete all events, user data, all data, and captured pictures, and restore device to factory settings or default settings. 1. Tap Data (Data Management) to enter the Data Management page. www.acti.com... - Page 26 You can view the device model, the serial No., the MAC address, the firmware version, the production date, and the open source code License. Tap Device to enter the Device page. NOTE: The device information page may vary according to different device models. www.acti.com...
-
Page 27: Appendix
User’s Manual Appendix Tips When Collecting / Comparing Face Picture Position (Recommended Distance: 0.5 m) The position when collecting or comparing face picture is as below: www.acti.com... -
Page 28: Expression
Posture In order to get a good quality and accurate face picture, position your face looking at the camera when collecting or comparing face pictures. Size Make sure your face is in the middle of the collecting window. www.acti.com... - Page 29 If installing the device outdoors, you should apply silicone sealant among the cable wiring area to keep raindrops from entering. Make sure the environment illumination is more than 100 Lux. If the light source is 0.5m away from the device, the illumination should not be less than 100 Lux. www.acti.com...
- Page 30 Daytime (Turn Human Body 0.3/0.26 m 0.56/0.5 m 1.03/1.06 m Camera Sunlight) Daytime (Turn Human Body 0.36 m 0.6 m 1.25 m device’s back to unlight) At Night Acrylic Black 0.56 m 0.83 m 1.25 m (Turn Light on) Wall www.acti.com...
- Page 31 Copyright © 2019, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.com...
Need help?
Do you have a question about the R71CF-34 and is the answer not in the manual?
Questions and answers