Related Manuals for Alcoa HUCK HK480
Summary of Contents for Alcoa HUCK HK480
- Page 1 NSTRUCTION ANUAL YDRAULIC NSTALLATION ® ® ® Makers of Huck , Marson , Recoil Brand Fasteners, Tools & Accessories November 25, 2015 HK480...
-
Page 2: Conformity
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) -
Page 3: Table Of Contents
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) ONTENTS EC D ......2 ECLARATION OF ONFORMITY . -
Page 4: Nstructions
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) AFETY NSTRUCTIONS 14. Where applicable, always clear spent pintail out of nose assembly before installing the next fastener. GLOSSARY OF TERMS AND SYMBOLS: 15. Check clearance between trigger and work piece to ensure Product complies with requirements set forth by the there is no pinch point when tool is activated. - Page 5 507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) AFETY NSTRUCTIONS (continued) IV. REPETITIVE MOTION HAZARDS: Wear warm clothing when working in cold conditions and 1. When using assembly power tool, the operator can keep hands warm and dry.
-
Page 6: Escription
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) ESCRIPTION The Huck 507 inline Hydraulic Installation Tool The correct PULL and RETURN pressures are ® installs C50L HUCKBOLT Fasteners and HLC50L important for the proper function of the tool and Nose HUCKLOK ®... -
Page 7: Peration
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) RINCIPLE OF PERATION Clamping pressure is applied to the sheets. The anvil is WARNING: Huck recommends that a Huck forced forward, swaging the collar into locking grooves ® POWERIG be used to power Huck tools. -
Page 8: Use
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) REPARATION FOR POWER SOURCE CONNECTIONS WARNINGS: ® ® ® Apply Parker Threadmate , Loctite 567, or Slic-Tite - Read entire manual before using tool. male pipe threads per manufacturer’s instructions. -
Page 9: Nstructions
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) PERATING NSTRUCTIONS NOTE: “Gap” is the space between sheets. It WARNINGS: is excessive if not enough of the pintail sticks - Wear approved eye and hearing through the collar for the nose assembly jaws to protection. -
Page 10: Aintenance
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) AINTENANCE - Apply continuous steady pressure to components. CAUTIONS: An arbor press provides steady pressure to press a - Consult the Material Safety Data Sheet component into or out of an assembly. -
Page 11: Isassembly
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) ENERAL ISASSEMBLY AND SSEMBLY UIDELINES During disassembly and assembly, take the following A special Spanner Wrench is available from Huck to precautions to avoid damaging tool or components: aid in the disassembly and assembly of Locking Ring, a. -
Page 12: Ssembly
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) SSEMBLY For component identifi cation, see Figure 1. Before 9. Position the cushion and handle assembly, and re-assembling the tool: insert four socket-head screws with lockwashers. NOTE: When re-assembling the tool, always replace... - Page 13 507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) SSEMBLY RAWING WITH UMBERS IGURE...
-
Page 14: Roubleshooting
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) ROUBLESHOOTING Always check the simplest possible cause (such as substitute known good parts for suspected defective a loose or disconnected trigger line) of a malfunction parts. Use this troubleshooting information to aid in fi... -
Page 15: Ccessories
507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) & CCESSORIES Huck has created product-specifi c Spare Parts Service when performing maintenance on it. Kits that contain various perishable parts. The types Huck also recommends having the following and quantities of spare parts that should be available Accessories available when preparing, using, and vary with the application and tools in use. - Page 16 507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) ERVICE OTES...
- Page 17 507 Hydraulic Installation Tool Alcoa Fastening Systems & Rings (HK480) IMITED ARRANTIES OTHER ITEMS MANUFACTURED BY THIRD OOLING ARRANTY PARTIES. HUCK EXPRESSLY DISCLAIMS Huck warrants that tooling and other items (excluding ANY WARRANTY EXPRESSED OR IMPLIED, fasteners, and hereinafter referred as “other items”)
- Page 18 About Alcoa Fastening Systems & Rings and industrial applications. Headquartered in Torrance, California, the company has over 8,300 employees at 39 Alcoa Fastening Systems & Rings, a business unit manufacturing and distribution/logistics locations in 13 of Alcoa, is a leading worldwide designer and countries.
Need help?
Do you have a question about the HUCK HK480 and is the answer not in the manual?
Questions and answers