Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alcoa Huck 2600 Series
Summary of Contents for Alcoa Huck 2600 Series
- Page 1 Distributed by Toll Free 1 800 563 1293 NSTRUCTION ANUAL YDRAULIC NSTALLATION OOLS 2600 2600-16-2T 2600 2600-16-2T 2600-12 2600-16-30T 2600-12 2600-16-30T 2600-16 2600-16-50T 2600-16 2600-16-50T 2600-16-3 2600-16-3 2600-16-12 2600-16-12 03-26-2012 HK914...
-
Page 2: Eu Declaration Of Conformity
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) -
Page 3: Table Of Contents
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) ONTENTS ONTENTS EU D ......2 ECLARATION OF CONFORMITY . -
Page 4: Afety
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) AFETY NSTRUCTIONS AFETY NSTRUCTIONS 11. Make sure proper power source is used at all times. GLOSSARY OF TERMS AND SYMBOLS: 12. Release tool trigger if power supply is interrupted. Product complies with requirements set forth by the relevant European directives. -
Page 5: Principle Of Operation
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) RINCIPLE PERATION RINCIPLE PERATION Piston Travel Pull Pressure Piston (Pull Cycle) When the Trigger Switch is depressed, pressurized hydraulic fluid moves through the PULL hose to the front side of the Piston. The piston and nose... -
Page 6: Pecifications
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) PECIFICATIONS PECIFICATIONS POWER SOURCE: MAX OPERATING TEMP: Huck POWERIG Hydraulic Unit 125°F (51.7°C) HOSE KITS: MAX FLOW RATE: Use only genuine HUCK Hose Kits rated @ 10,000 2 gpm (7.5 l/m) psi working pressure. -
Page 8: Operating Instructions
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) PERATING NSTRUCTIONS PERATING NSTRUCTIONS WARNING: Reasonable care of installation nose assembly jaws to grab onto. tools by operators is an important factor in maintaining tool effeciency and in reducing 2. Put fastener into hole. -
Page 9: Disassembly
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) ISASSEMBLY ISASSEMBLY Piston Assembly Tool onto Piston. Press or drive For component identification, see Figure 6 and P ARTS NOTE: The following procedure is for complete Piston, Front Gland (8) and Rear Gland out of disassembly of tool. -
Page 10: Reparation For Use
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) SSEMBLY SSEMBLY 11. Lubricate inside of Press Figure 4 For component identification, see Figure 6 and P ARTS NOTE: Clean components with mineral spirits or similar assembled Rear solvent. Inspect for wear/damage and replace as necessary. -
Page 11: Assembly Drawing
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) SSEMBLY RAWING SSEMBLY RAWING 6 7 8 9 10 Sticker Locations (2600 & 2600-12 only) 2600 2600-12 2600-16 2600-16-3 2600-16-2T 2600-16-12 2600-16-30T 2600-16-50T PULL PRESSURE NOTE REVERSAL OF HOSE FITTING LOCATION OF 2600-16-2T, 2600-16-30T, & 2600-16-50T... -
Page 12: Parts
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) ARTS IGURE ARTS IGURE 2600 2600-16 2600-16-12 2600-16-30T Item Description 2600-12 2600-16-3 2600-16-2T 2600-16-50T 1 Piston 122759 125467 2 Retaining Nut 122756 3 Front Wiper Seal 505064 4 Front Wiper Housing 122758... -
Page 13: Ydraulic Ouplings
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) YDRAULIC OUPLINGS YDRAULIC OUPLINGS TICKER OCATIONS TICKER OCATIONS The 2600 series tools come labeled with Sticker part number 590424-7400, which contains safety and pressure settings information. It is necessary that this sticker remain on the tool and is easily read. -
Page 14: Troubleshooting
2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) ROUBLESHOOTING ROUBLESHOOTING 9. Tool "hangs up" on swaged collar of fastener. a. Improper tool operation. See No. 6. b. RETURN pressure too low. c. Not enough collar lubricant. Always check the simplest possible cause of a d. - Page 15 2600 series Hydraulic Tooling Alcoa Fastening Systems (HK914) IMITED ARRANTIES IMITED ARRANTIES TO THE TOOLING, PART(S) OR OTHER ITEMS OOLING ARRANTY MANUFACTURED BY THIRD PARTIES. HUCK Huck warrants that tooling and other items (excluding EXPRESSLY DISCLAIMS ANY WARRANTY fasteners, and hereinafter referred as "other items")
- Page 16 251 Cree Crescent, Winnipeg, MB Canada R3J 3X4 Tel : 204 837 8361 1 800 563 1293 • Fax: 204 837 3520 1 800 974 1494 • applifast.com...
Need help?
Do you have a question about the Huck 2600 Series and is the answer not in the manual?
Questions and answers