Harken 1134 Instructions

Harken 1134 Instructions

Small boat continuous line-drive furler

Advertisement

Telephone: (262) 691-3320 • Fax: (262) 701-5780 • Web: www.harken.com • Email: harken@harken.com
Use the continuous line-drive furler for high-performance skiffs, dinghies, sportboats, and multihulls
using large jibs, reaching, and offwind asymmetrical sails. It can also furl staysails on offshore boats.
Features:
Drive sheave furler never runs out of line and can completely furl any sized sail.
Line is easy to install and remove from sheave without disassembly.
Offset holes in the drive sheave grip line securely.
Stripper and feeder work together to prevent line from jamming.
Line guard adjusts in 90-degree increments to accommodate attachments to the boat.
Requirements:
Sail with torsion rope or 1 X 19 counter-laid stainless steel wire sewn into the luff with thimbles
that are stitched to the tack and head so they will not turn.
164 upper swivel
For a hoistable jib furling system, purchase an additional 464 hoistable halyard swivel and
adapter tang. See instruction manual 4350 on www.harken.com
Feeder
Stripper
.
Pin-to-pin
Drum
length
Ø
in
mm
in
2 11/16
68
2 7/8
I N S T R U C T I O N S
1134 Small Boat Continuous Line-drive Furler
N15W24983 Bluemound Road • Pewaukee, WI 53072 U.S.A.

Description, Features, and Requirements

Line
Ø
mm
in
mm
73
3/16
5
5/16
Drive sheave
Line guard

1134 Specifications

Jaw
Max luff
width
wire Ø
in
mm
in
mm
8
1/8
3
Purchase
separately
164 upper swivel
Hoistable system components
464 hoistable swivel
Clevis pin
Ø
Weight
in
mm
oz
1/4
6.4
5.4
154
479, 480, 481
tangs
Maximum
working load
g
lb
kg
950
431

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1134 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Harken 1134

  • Page 1 1134 Small Boat Continuous Line-drive Furler N15W24983 Bluemound Road • Pewaukee, WI 53072 U.S.A. Telephone: (262) 691-3320 • Fax: (262) 701-5780 • Web: www.harken.com • Email: harken@harken.com Description, Features, and Requirements Use the continuous line-drive furler for high-performance skiffs, dinghies, sportboats, and multihulls using large jibs, reaching, and offwind asymmetrical sails.
  • Page 2 Dimensions Dimensions shown in [inches ] and millimeters 3.247 82.47 0.312 7.92 Furling Line - Type and Loading Consult rigger for best type of continuous furling line and end-for-end splice. A smooth splice is critical for smooth furling operation. Loading line onto furler: A.
  • Page 3 Rotating Guard Use this procedure to change the clevis pin orientation for either fore/aft or athwartships direction to match boat’s chainplate. Loosen the screws about three rotations. The screws seat in detents. Rotate the lower fork so that it is 90°. See image at bottom of page.
  • Page 4 Maintenance Remove line from drive sheave. Clean furler with detergent and fresh water applied into drive sheave. Rotate drive sheave to distribute. Be sure to squirt into area just inside locking ring to clean bearings as shown by arrows at right. Flush with fresh water while rotating parts. Inspect pins and rings to make sure they are secure.

Table of Contents