Stanley Fatmax FME190 Original Instructions Manual page 7

Note! Tighten the connection hand tight at first, before using
the spanners.
Removing/Replacing (Fig.E, Fig.F)
Lock the socket (3) with one mounting spanner (9) and
u
loosen the shaft (4) anticlockwise with another mounting
spanner (9) gripping the welded nut (Fig. E).
Loosen the welded nut anticlockwise (Fig. F) and remove
u
the shaft (4) from the socket (3) (Fig. F)
Stirrer (Fig.G, Fig.H)
Lock the welded nut of the shaft (4) with one mounting
u
spanner (9) and loosen the stirrer (5) anticlockwise with
another mounting spanner (9) gripping the welded nut
(Fig. G).
Loosen the welded nut anticlockwise (Fig. H) and remove
u
the stirrer (5) from the shaft (4) (Fig. H).
Attach a new shaft/stirrer as required.
u
Use
Variable speed switch (Fig.I)
Operate the product either in instant or continuous mode.
Instant Mode
Switch the product on by pressing the variable speed
u
switch (7) (Fig. I).
Switch the product off by releasing the variable speed
u
switch (7).
Continuous mode
Switch the product on by pressing the variable speed
u
switch (7) and hold it in position (Fig. J, step 1).
Press the lock-on button (6) and hold it in position to lock
u
the variable speed switch (7) (Fig. I, step 2).
Release the lock-on button (6) and variable speed switch
u
(8). The variable speed switch is now locked on for
continuous use.
Depress and release the variable speed switch (7) to
u
switch the product off.
General operation
Check the product, its power cord and plug as well as
u
accessories for damage before each use. Do not use the
product if it is damaged or shows wear.
Double check that the accessories and attachments are
u
properly fixed.
Always hold the product on its handles. Keep the handles
u
dry to ensure safe support.
Ensure that the air vents are always unobstructed and
u
clear. Clean them if necessary with a soft brush. Blocked
air vents may lead to overheating and damage the
product.
(Original instructions)
Switch the product off immediately if you are disturbed
u
while working by other people entering the working area.
Always let the product come to complete stop before
putting it down.
Do not overwork yourself. Take regular breaks to ensure
u
you can concentrate on the work and have full control over
the product.
Mixing (Fig.K)
Warning! During operation fine dust will be generated!
Some dusts are highly inflammable and explosive! Do not
smoke during operation, keep heat sources and open flames
out of the working area! Always wear a dust mask to protect
yourself against hazards resulting from fine dust!
The stirrer will come to a stop during operation if the material
is too firm! Switch the product off, lift the stirrer out of the
material and inspect the material before using the product
again! A blocked stirrer may cause overheating the of the
motor. Hold the product firmly during operation. Do not let the
stirrer touch the bucket! This can cause damage to the stirrer
and bucket!
Hold the product with 2 hands on both handles (2) and
u
insert the stirrer (5) into the material (Fig. M).
Gently press variable speed trigger switch to start
u
operation at a low speed.
Move the stirrer through the material until it is evenly and
u
completely mixed.
Switch the product off. Let the stirrer come to a complete
u
stop before lifting it out of the mixing material.
Warning: Switch the product off, let it come to a complete
stop and disconnect it from the power supply if the stirrer
gets stuck in the mixing material. Only then free the jammed
attachment.
After use
Warning: Always switch the product off, disconnect the
product from the power supply and let the product cool down
before performing inspection, maintenance and cleaning work!
Cleaning
Keep the product clean. Remove debris from it after each
u
use and before storage.
Regular and proper cleaning will help ensure safe use and
u
prolong the life of the product.
Inspect the product before each use for worn and
u
damaged parts. Do not operate it if you find broken and
worn parts.
Warning: Only perform repairs and maintenance work
according to these instructions! All further works must be
performed by a qualified specialist!
Clean the product with a dry cloth. Use a brush for areas
u
that are hard to reach.
ENGLISH
7