Draper Skylight FlexShades Installation Instructions
Draper Skylight FlexShades Installation Instructions

Draper Skylight FlexShades Installation Instructions

Advertisement

Read entire procedure before installing. Keep instructions for future
reference.
Tools needed for installation: Cordless drill/screwdriver, with flathead,
phillips, and
1
/
" nut driver attachments (magnetized, if possible),
4
1
extensions, and
/
" drill bit; Carpenter's level; Hack saw; Aluminum file;
8
Square; Stiff" tape measure or zig-zag rule; and
hole punch.
Use extreme care during installation to avoid scratching finish on
Skylight parts.
Use drawings on back page as reference throughout installation.
Headboxes and side channels must be installed level and square.
Controls may be shipped separately, or in same carton as shades; do
not discard with packing material.
Please follow installation guidelines carefully. Failure to do so invalidates
warranty.

Installation Preparation

Arrange pieces on floor in the general manner they are to be installed. All
four corners are color coded by tape for easy matching.
Remove covers from both headboxes (see Fig. 1).
Remove spring roller from its headbox. The one-notch spring roller is pre-
tensioned and the dog is locked in the notch.
Remove roller/motor assembly from its headbox by removing the black
plastic retainer clip at the idler end and the retainer pins from the motor
end. Take the idler end out of its bracket, then slide the motor end off the
motor studs on the endcap (see Fig. 2). Keep all retainer clips and pins.
Retainer clip
Idler End
Crank Endcap
411 S. Pearl St., Spiceland, IN 47385 USA 765-987-7999 fax 765-987-7142
e-mail draper@draperinc.com
Copyright © 2000

Installation Instructions

Skylight FlexShades by Draper
Caution
7
/
" electrical knockout
8
Face Cover
Figure 1
Retainer Pin
Motor End
Figure 2
www.draperinc.com
Form FSSLi00
Printed in U.S.A.
If the shade has a detachable crank handle, remove the universal joint
from the bottom of the end cap by removing 2 screws. (Fig. 3). Save
universal joint & screws.
Tube
Crank Roller
Insert
Insert Shaft
NOTE: If unit is motorized, you may need to locate and drill a hole for the
conduit connector (Conduit connector is not supplied) (see Fig. 4).
3
/
"
4
5
/
"
8
3
/
"
4
1
1
/
"
2
5
/
"
8

Unit Assembly/Installation

With unit still on floor, install both side channels to both headboxes (see
Fig. 5). Make sure channel locators are properly seated; tap gently with
plastic hammer or rubber mallet if necessary. NOTE: Fabric travels toward
motor end.
Channel locator
Insert four fabric guides into side channel grooves to help funnel fabric into
the channels (see Fig. 14). Make sure the bevel, or bent portion, is placed
facing up if inside mount, and down if outside mount.
Steel stay
Rivet
Fabric
guide
Channel
locator
Fabric
Light seal
retainer
Roller
Figure 3
Outside mount
1
1
/
"
2
Inside mount
Figure 4
Fabric guide
Figure 5
Side
Channel
Stay pocket
Figure 14
Fabric

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Skylight FlexShades and is the answer not in the manual?

Questions and answers

Summary of Contents for Draper Skylight FlexShades

  • Page 1: Installation Instructions

    Installation Instructions Skylight FlexShades by Draper If the shade has a detachable crank handle, remove the universal joint Caution from the bottom of the end cap by removing 2 screws. (Fig. 3). Save Read entire procedure before installing. Keep instructions for future universal joint &...
  • Page 2 For Inside Mount— Make sure Skylight unit is square. Note: Skylight FlexShades can be installed up and down slopes, but not Fasten cable support plates to structure through outboard holes in plate sideways along slopes. Headboxes must be installed level.
  • Page 3: Electrical Connections

    NOTE: Limit switches can be set with a single motor switch on a test cord Ribbon furnished by Draper, Inc. upon request. For multiple unit installations, each shade’s limit switch must be set before hooking them up to a group control feed tool system.
  • Page 4 2" dia. motorized roller Access cover 4" Access cover 4" Direction of Fabric Travel If you encounter any difficulties installing or servicing your Skylight FlexShade, call your dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999, fax (765) 987- 7142, or e-mail draper@draperinc.com.

Table of Contents