Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Javad Manuals
  4. Transmitter
  5. TRIUMPH-VS
  6. Configuration example

Javad TRIUMPH-VS Configuration Example

External uhf
Hide thumbs Also See for TRIUMPH-VS:

Advertisement

Quick Links

Download this manual
External UHF via
TRIUMPH-VS
Configuration Example
Version 1.0
Last Revised: April 28, 2012
All contents in this manual are copyrighted by JAVAD GNSS.
All rights reserved.The information contained herein may not be used, accessed, copied,
stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express written
consent from JAVAD GNSS

Advertisement

loading

Related Manuals for Javad TRIUMPH-VS

Summary of Contents for Javad TRIUMPH-VS

  • Page 1 Version 1.0 Last Revised: April 28, 2012 All contents in this manual are copyrighted by JAVAD GNSS. All rights reserved.The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express written...

  • Page 2: External Configuration

    2. Connect your HPT435BT to PC using serial port. Power the modem. 3. Start ModemVU software. 4. Select HPT435BT from the list, click Ok. Then select the port the modem is connected to and click Connect: Figure 1. Connecting to ModemVU www.javad.com...
  • Page 3 • PIN code - enter the PIN code of the module; • Mode - set to Slave; • BT - set to ON to activate the Bluetooth module and click Apply. 1. Starting version 3.1 Bluetooth connection and connection with TRIUMPH-VS is supported. www.javad.com...
  • Page 4 Received data to to BT, click Apply. Figure 4. Serial Interface & Tools tab External UHF Modem Configuring To configure external UHF modem HPT435BT using TRIUMPH-VS receiver, follow the instructions below: 1. Attach antenna to the HPT435BT. Warning: Always attach antenna before turning on! Do not use the radio without antenna, to avoid the serious damage of the equipment.
  • Page 5 Figure 5. Connection Mode 7. Tap Local Settings and ensure that PIN is the same as has been configured in the ModemVU, tap Apply. Figure 6. Properties 8. Tap Discover and then select Bluetooth Name of External UHF in the list. www.javad.com...
  • Page 6 External UHF Modem Configuration External UHF Modem Configuring 9. Tap Connect. Figure 7. Bluetooth 10. Tap on the Bluetooth icon. Ensure parameters in the right column are not “--”. Figure 8. BT STATUS 11. On the Main screen tap SettingsCommunicationUHF. www.javad.com...

  • Page 7: Base Configuration

    12. Configure parameters such as Frequency, Output Power and Protocol. Figure 9. HPT435BT Note: For base station set the output power to 35000 mW, to provide the best transmitting coverage. Base Configuration 1. On the Main screen tap SettingsActions and select Fixed Base Station: Figure 10. Actions www.javad.com...
  • Page 8 External UHF Modem Configuration Base Configuration 2. Press FN button on the front panel of Triumph-VS to switch to Action screen: Figure 11. Action Screen 3. Tap Yellow Stone 84 on the top of the screen to open the screen with the Fixed Base Station parameters.

  • Page 9: Rover Configuration

    1. To set up the receiving of correction tap on the Main screen SettingsGNSSReceive Data (Rover). 2. Select UHF and corrections format. 3. Click on the UHF icon and check the LQ, Delay, Received and Lost parameters. Figure 14. RADIO STATUS (Rover) www.javad.com...
  • Page 10 900 Rock Avenue, San Jose, CA 95131 USA Phone: +1(408)770-1770 Fax: +1(408)770-1799 www.javad.com Copyright © JAVAD GNSS, Inc., 2012 All rights reserved. No unauthorized duplication.