Download Print this page

Siemens SITRANS LU AO Quick Start Manual

Continuous level measurement - ultrasonic controllers

Advertisement

Quick Links

Level Measurement
Continuous level measurement - Ultrasonic controllers
SITRANS LU AO
Overview
4
The SITRANS LU AO Analog Output Module provides remote
analog output for the measurement points of the SITRANS LU10
level monitor.
Benefits
• Analog outputs can be up to 1 500 m (5 000 ft) from the
SITRANS LU 10
• Analog outputs can be per transducer and/or average of 2 or
more
Application
The operation of the SITRANS LU AO is programmed via the
SITRANS LU10. The only on-board settings are for bank selec-
tion and output testing.
The SITRANS LU AO can provide up to 10 analog outputs (each
sharing a common negative bus which is electrically isolated
from ground).
4/168
Siemens FI 01 · June 2015
© Siemens AG 2015
Technical specifications
Mode of operation
Input
Communications
Transmission rate
Voltage
Polarization
Max. load
Output
Analog outputs
± 20 mA bipolar current loop
• Max. load
• Resolution
Rated operating conditions
Ambient conditions
• Ambient temperature for enclosure
• Location
• Installation category
• Pollution degree
Design
Weight
Material (enclosure)
Degree of protection
• Cable connection
• Electrical connection and relay
connection
Power supply
Displays and controls
Certificates and approvals
Selection and Ordering data
SITRANS LU AO
Provides remote analog output for the
measurement points of the SITRANS LU10
level monitor.
Approvals: CSA
, FM, CE, RCM
US/C
Operating Instructions
English
German
Note: Operating Instructions should be
ordered as a separate line item on the order.
This device is shipped with the Siemens Milltronics
manual DVD containing the Quick Start and Opera-
ting Instructions library.
Accessories
Sun Shield, 304 stainless steel
Data from SITRANS LU10
4 800 bits/s
± 20 mA bipolar current loop
Non-polarized
1 receiving unit
10 analog outputs, programmable
from SITRANS LU10
0 or 4 ... 20 mA, isolated
Input and transmission
750 Ω
0.1 %
-20 ... +50 °C (-5 ... +122 °F)
Indoor/outdoor
II
4
2 kg (4.4 lb)
Polycarbonate
Type 4X/NEMA 4X/IP65
2 copper conductors, twisted, with
foil shield/drain wire, 300 V
0.5 ... 0.75 mm² (22 ... 18 AWG)
Copper conductor according to local
requirements, rated 250 V 5 A
100/115/200/230 V AC ± 15 %,
50/60 Hz, 15 VA
1 LED for display of voltage/
communications state
CE, FM, CSA
, RCM
US/C
Article No.
7ML5810-1A
7ML1998-5CE01
7ML1998-5CE31
7ML1930-1GA

Advertisement

loading

Summary of Contents for Siemens SITRANS LU AO

  • Page 1 100/115/200/230 V AC ± 15 %, tion and output testing. 50/60 Hz, 15 VA The SITRANS LU AO can provide up to 10 analog outputs (each Displays and controls 1 LED for display of voltage/ sharing a common negative bus which is electrically isolated communications state from ground).
  • Page 2 2. Refer to associated application device instruction manual for wiring detail. Check that the communication parameter P740 (SITRANS LU10) is ON. 3. SITRANS LU AO interconnecting cable shield should be grounded at SITRANS LU10 only. Insulate shields at junctions to prevent inadvertent grounding.