Mounting The Mvc 121; Tabletop Use; Rack Mounting; Furniture Or Projector Mounting - Extron electronics MVC 121 User Manual

im Vertrieb von
Installation and Operation

Mounting the MVC 121

The one rack unit high, quarter rack wide MVC can be set on a
table, mounted on a rack shelf, mounted under a desk or
tabletop, or mounted on a projector bracket.

Tabletop use

Each MVC comes with rubber feet. For tabletop use, attach a
self-adhesive rubber foot to each corner of the bottom of the
unit.

Rack mounting

For optional rack mounting, do not install the rubber feet.
Mount the MVC on a VersaTools
part #60-190-20 or #60-604-20) or a standard Universal 1U Rack
Shelf (Extron part #60-190-01 or #60-604-01). On the standard
rack shelf, the MVC mounts in one of four locations to the rear
of the rack or in one of four locations to the front of the rack.
If rubber feet were previously installed on the bottom of
1.
the MVC, remove them.
2. Mount the MVC on the rack shelf, using two 4-40 x 3/16"
screws in opposite (diagonal) corners to secure the MVC
to the shelf.
VersaTools Rack Shelf
1/4 Rack Width
False Front Face Plate
Use 2 mounting holes
on opposite corners
Mounting the MVC on a VersaTools rack shelf
Only products in the VersaTools line can be mounted to
a VersaTools shelf. Most 1U rack-mountable Extron
products can be mounted on the standard shelf.
www.camboard.de
MVC 121 • Installation and Operation
2-2
®
19" 1U Rack Shelf (Extron
DI
ST RI
BU
TI ON
AM
PL
IF IE
R
DI
ST
RI BU
TI ON
AM
PL IF IE
R
M IC
1
M IC
2
M AI
N 3
M AS
TE
R
MI
XE R/
VO
LU
ME
CO
NT RO
LL
ER
(2) 4-40 x 3/16" screws
CAMBOARD Electronics

Furniture or projector mounting

Tel. 07131 911201
Fax 07131 911203
AU
TO SW
ICH MO
DE
1 NO
RM AL
AU
2 TO
3
4
A/ V SW
M IC
IT CH 1
ER
M IC
2
M AI
N
3
M AS
TE
R
M IX
ER
/V OL
UM
E CO
NT
RO LL
ER
Mounting the MVC on a standard 1U rack shelf
3. Install blank panel(s) or other unit(s) on the rack shelf.
Furniture mount or projector mount the MVC using the
optional mounting kit (part #70-212-01, furniture; or 70-217-01,
projector) as follows:
1. Attach the mounting brackets to the MVC with the
machine screws provided.
2. If feet were previously installed on the bottom of the
MVC, remove them.
For furniture mounting
3a. Hold the MVC with the attached brackets against the
underside of the table or other furniture. Mark the
location of the screw holes of the bracket on the mounting
surface.
4a. Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)
deep in the mounting surface at the marked screw
locations.
5a. Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until just less than
1/4" of the screw protrudes.
ce-info@camboard.de
MVC 121 • Installation and Operation
DI ST
RI BU
TI ON
AM
PL
IF IE
R
M D
DI ST A S
RI BU E R
TIO IE S
N AM
PL IFI ER
2-3