Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cisco TelePresence Advanced Media Gateway 3610
Summary of Contents for Cisco TelePresence Advanced Media Gateway 3610
- Page 1 Cisco TelePresence Advanced Media Gateway 3610 Getting started 61-0035-03...
-
Page 2: Table Of Contents
Contents General information ........................ 3 About the Cisco TelePresence Advanced Media Gateway 3610 ....3 Package contents ......................3 Port and LED locations ....................3 LED behavior ..........................5 Front panel LED behavior ..................5 Rear panel LED behavior ..................6 Connecting the Cisco AM GW 3610 ................... -
Page 3: General Information
General information General information About the Cisco TelePresence Advanced Media Gateway 3610 The Cisco TelePresence Advanced Media Gateway 3610 (Cisco AM GW 3610) combines with the Cisco TelePresence Video Communication Server (Cisco VCS) to create a unified communications solution. ®... - Page 4 General information Figure 2: Cisco AM GW 3610 rear panel Air Exhaust Link Connectors Power Supply 1000 1000 1000 1000 Link Link Ethernet C Ethernet A Ethernet B Ethernet D Admin Link In Link Out Ethernet Ports and Admin Port and...
-
Page 5: Led Behavior
LED behavior LED behavior Front panel LED behavior Table 1 describes the behavior of the LEDs on the front of the gateway. Table 1: Cisco AM GW 3610 front panel LED behavior Color Indicates Status Green The gateway is operating normally... -
Page 6: Rear Panel Led Behavior
LED behavior Rear panel LED behavior Table 2 describes the behavior of the LEDs on the rear of the gateway. Table 2: Cisco AM GW 3610 rear panel LED behavior Color Indicates Ethernet Port Status: Green The link has been established as a full-... -
Page 7: Connecting The Cisco Am Gw 3610
Connecting the Cisco AM GW 3610 Connecting the Cisco AM GW 3610 Before you start Before installing the gateway, you must read the safety Important: information at http://www.cisco.com/go/telepresence/safety Step one: Connect power Connect the power connector on the rear of the unit to the power supply using the supplied power cable (there is no On/Off switch). -
Page 8: Initial Configuration
AMGW:> Step two: Configure Ethernet Port A settings The default setting for the Cisco AM GW 3610 Ethernet ports is auto-sensing mode. If the switch ports to which you connect the gateway are not also set to auto-sensing mode, then you need to configure the gateway Ethernet ports to use the same speed and duplex mode. -
Page 9: Step Three: Assign An Ip Address To The Gateway (Optional)
Initial configuration Step three: Assign an IP address to the gateway (optional) The default setting for the gateway is to use DHCP to obtain an IP address. If you want the IP address of the gateway to be assigned by your DHCP server, omit this step. -
Page 10: Configuring The Cisco Am Gw 3610
Currently, only the Cisco VCS is supported as a proxy server to the gateway. The gateway must be configured as a neighbor zone of each Cisco VCS in the proxy list that is running software version X6.1 or earlier – this is not needed for any Cisco VCS that is running software version X7 or later. -
Page 11: Step Three: Set The Video Capacity
Configuring the Cisco AM GW 3610 Step three: Set the video capacity The gateway can be configured in either of the following video capacity modes: Standard Definition (SD) mode (CIF and VGA resolutions supported) High Definition (HD) mode (CIF, VGA and 720P resolutions supported) ... -
Page 12: Checking For Updates
Checking for updates Checking for updates We recommend that you regularly check the web site at http://www.cisco.com/ cisco/web/support/index.html for updates to the main software image for the gateway. This section describes how to upgrade the gateway using the web (you can also upgrade the gateway using FTP). -
Page 13: Replacing The Power Supply
Replacing the power supply Replacing the power supply Only replace the power supply under the guidance of Cisco customer support. The power supply will be installed when you receive your gateway. To replace the power supply: Remove the power cable from the unit to disconnect the power. -
Page 14: Troubleshooting And Technical Support Information
versions of the online help, reference guides, and articles that cover many frequently asked questions, get help from the Cisco Technical Support team. Make sure you have the following information ready before raising a case: the serial number and product model number of the unit (if applicable) ... -
Page 15: Technical Specifications
Technical specifications Technical specifications Power requirements Table 3: Cisco AM GW 3610 ratings Rating Value Nominal voltage 115V to 230V 50/60 Hz Current rating 9A Maximum Supply voltage range 100 to 240V 50/60 Hz Over-current protection Ensure the supply to this unit is protected by a branch circuit protector rated by a maximum of 20A. -
Page 16: Disclaimers And Notices
THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. www.cisco.com/go/ and other countries. A listing of Cisco's trademarks can be found at trademarks .
Need help?
Do you have a question about the TelePresence Advanced Media Gateway 3610 and is the answer not in the manual?
Questions and answers