Subscribe to Our Youtube Channel
Related Manuals for Lenze G-motion GPA Series
Summary of Contents for Lenze G-motion GPA Series
- Page 1 Show/Hide Bookmarks BA 12.0030 .ð.$ Operating Instructions G-motion GPA servo planetary geared motors...
- Page 2 Show/Hide Bookmarks Product key Input design Gearbox Gearbox Step Output design Drive size type size number Square flange (through Solid shaft Planetary gearbox holes) smooth servo motor, Without foot mounting with centering asynchronous, externally ventilated Servomotor, synchronous, externally ventilated Expanded servomotor key .
- Page 3 Show/Hide Bookmarks GPA mounting positions A, C, D Nameplate (sample) Hans-Lenze-Strasse 1 Made in D-31855 Aerzen File no. Germany http://www.Lenze.com 3~MOT GPA00-1SGCN-09FN38 330 V 1.2 kW 3750 min 12 Nm 938 min 1eck 2eck 2.5 A 1.6 HP c = 2.1...
- Page 4 1st edition Completion of the product key Completion of the chart transport weights © 2004 Lenze Drive Systems GmbH Hans-Lenze-Straße 1 31855 Aerzen No part of this documentation may be reproduced or made accessible to third parties without written consent by...
-
Page 5: Table Of Contents
............Lenze drive systems . -
Page 6: Preface And General Information
ƒ After receipt of the supply, check immediately whether it corresponds with the accompanying papers. Lenze does not grant any warranty for subsequent claims. Claim for – visible transport damages immediately to the forwarder. -
Page 7: Lenze Drive Systems
– operating faults, – disregarding the Operating Instructions. Warranty ƒ Conditions of warranty: see terms of sale and delivery of Lenze Drive Systems GmbH. ƒ Warranty claims must be made to Lenze immediately after detecting the deficiency or fault. ƒ The warranty is void where liability claims cannot be made. -
Page 8: Safety
ƒ Operate the drive system only when it is in a proper state. ƒ Retrofittings, modifications, or redesigns of the drive system are basically prohibited. Lenze must be contacted in all cases. BA 12.0030 EN 2.0... -
Page 9: Definition Of Notes Used
Show/Hide Bookmarks Safety Definition of notes used Definition of notes used The following signal words and symbols are used in this documentation to indicate dangers and important information: Safety instructions Structure of safety instructions: Danger! (characterises the type and severity of danger) Note (describes the danger and gives information about how to prevent dangerous situations) -
Page 10: Technical Data
Show/Hide Bookmarks Technical data Product features Technical data ƒ The most important technical data are indicated on the nameplate (for Design and Contents see page 3). ƒ Additional technical data are listed in the product catalogues. Product features Design Drive systems have a modular design. They consist of: ƒ... -
Page 11: Transport Weights
Show/Hide Bookmarks Technical data Transport weights Transport weights Geared servo motor Drive size (square measure) - S GCN GPA 00 - 1 < 6 < 10 GPA 01 - 1 < 8 < 12 < 19 GPA 02 - 1 <... -
Page 12: General Data/Operating Conditions
Show/Hide Bookmarks Technical data General data/operating conditions Temperatures General data/operating conditions 3.3.1 Temperatures The permissible temperature range is determined by the following: ƒ The lubricant specifications in connection with the expected oil temperatures in operation (see chapter 7.1 and nameplate). ƒ... -
Page 13: Mechanische Installation
Show/Hide Bookmarks Mechanical installation Storage Mechanische Installation Danger! Only transport the drive with transport equipment or hoists which are suitable for this load (see transport weights, chapter 3.2). Ensure a safe fixing. Avoid shocks! The motors attached to the gearbox are partially equipped with eyebolts. These are exclusively determined for motor/gearbox mounting and dismounting and must not be used for the complete geared motor! Storage... -
Page 14: General Information About The Assembly Of Drive Systems
Show/Hide Bookmarks Mechanical installation Mounting General information about the assembly of drive systems 4.2.2 General information about the assembly of drive systems ƒ Take safety measures prior to any operation: – Disconnect the machine from the mains, ensure standstill of the machine and avoid any machine movement. -
Page 15: Electrical Installation
Show/Hide Bookmarks Electrical installation Electrical installation Danger! Electrical connections must only be made by skilled personnel! Motor connection To correctly connect the motor options, please observe: ƒ the notes in the terminal box of the motor ƒ the notes in the Operating Instructions of the motor ƒ... -
Page 16: Commissioning And Operation
– loose fixing elements, – the condition of the electrical cables. ƒ If any interference should occur, proceed according to the troubleshooting list in chapter 8. If the interference cannot be eliminated, please contact the Lenze Service. BA 12.0030 EN 2.0... -
Page 17: Maintenance
Show/Hide Bookmarks Maintenance Maintenance intervals Maintenance Gearboxes and geared motors from Lenze are filled with a drive-specific and design-specific lubricant filling at delivery. The mounting position and design are decisive at ordering for the required lubricant quantity. Note! When changing the lubricant, Lenze recommends also changing the grease... -
Page 18: Replacing The Lubricant
Show/Hide Bookmarks Maintenance Maintenance intervals Replacing the lubricant 7.1.1 Replacing the lubricant Stop! Gearbox should be warm. ƒ Secure drive system and machine from inadvertent movement and mains ƒ connection. 1. Drain lubricant by removing the oil drain/filler plug. 2. Fill recommended lubricant in the specified amount. 3. -
Page 19: Lubricant Quantity
Show/Hide Bookmarks Maintenance Maintenance intervals Lubricant quantity 7.1.2 Lubricant quantity Gearbox Mounting position GPA 00 - 1 GPA 01 - 1 GPA 02 - 1 GPA 03 - 1 GPA 04 - 1 GPA 05 - 1 GPA 00 - 2 GPA 01 - 2 GPA 02 - 2 GPA 03 - 2... -
Page 20: Troubleshooting And Fault Elimination
If any malfunctions should occur during operation of the drive system, please check the possible causes using the following table. If the fault cannot be eliminated by one of the listed measures, please contact the Lenze Service. Fault Possible cause... -
Page 21: Disposal
Show/Hide Bookmarks Disposal Disposal Protect the environment! Packaging material can be recycled. What? Where? Transport material Pallets Return to the manufacturer or forwarder Packaging material Cardboard box to waste paper Plastics to plastics recycling or residual waste Reuse or dispose of wood wool Lubricants Oil, grease Dispose according to current regulations... -
Page 22: Appendix
Manufacturer’s Certification Herewith we declare that the products stated below are determined for assembly in a machine Lenze Drive Systems GmbH or for assembling a machine with other components. The commissioning of the machine is P.O. box 10 13 52 prohibited as long as it has been ascertained that it meets the EC Directive 98/37/EC. - Page 23 Show/Hide Bookmarks Lenze Drive Systems GmbH BA 12.0030 2.0 09/2004 TD09 2004 Hans-Lenze-Straße 1 31855 Aerzen Germany +49 (0) 51 54 82-0 Service 00 80 00 24 4 68 77 (24 h helpline) Service +49 (0) 51 54 82-1112 E-Mail Lenze@Lenze.de...
Need help?
Do you have a question about the G-motion GPA Series and is the answer not in the manual?
Questions and answers