Advertisement
Quick Links
AutoScan
to MultiScan
t
1. Introduction
2. AutoScan to MultiScan
Replacement
Preparing for Replacement
E 1998 Nordson Corporation
All rights reserved
Replacement Kit
r
WARNING: Allow only qualified personnel to perform the
following tasks. Observe and follow the safety instructions in
this document and all other related documentation.
Series 3000 hot melt units that have an AutoScan control system may be
field-retrofitted with a MultiScan control system. This service kit contains
the parts and instructions necessary for replacing an AutoScan control
system with a MultiScan control system.
Use the parts from the service kit and the following instructions to replace
an AutoScan control system with a MultiScan control system. Refer to
Parts for a list of the parts contained in the service kit.
Follow this procedure to ensure that personnel and equipment are
protected from electrical hazards.
WARNING: Risk of personal injury or death. Disconnect
equipment from all power sources before servicing.
1. Turn off the unit; then disconnect and lock out electrical power to the
unit.
2. See Figure 1. Remove the electrical cabinet lid (1).
3. Loosen the nuts (3) and captive screws (2) that secure the
control-end frame (4) and slide the frame out.
303 866A
Issued 12/98
Instruction Sheet
P/N 303 866A
Manual 57-41
Advertisement
Related Manuals for Nordson AutoScan
Summary of Contents for Nordson AutoScan
- Page 1 Observe and follow the safety instructions in this document and all other related documentation. Series 3000 hot melt units that have an AutoScan control system may be 1. Introduction field-retrofitted with a MultiScan control system. This service kit contains the parts and instructions necessary for replacing an AutoScan control system with a MultiScan control system.
-
Page 2: Preparing For Replacement
Replacement Kit Preparing for Replacement (contd) 4130818A Fig. 1 Opening the Electrical Cabinet 1. Electrical cabinet lid 3. Nut 2. Captive screw 4. Control-end frame (slides out) E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98... - Page 3 AutoScant to MultiScan Replacement Kit Follow this procedure to remove the AutoScan control-end frame. Removing the AutoScan Control System 1. Label or note existing wire connections for later reference. 2. See Figure 2. Disconnect the following ribbon cables and power...
- Page 4 AutoScant to MultiScan Replacement Kit 3. See Figure 3. Disconnect the terminal block plugs (2) from the Removing the AutoScan AutoScan input/output (I/O) board (1). Do not remove the wiring from Control System (contd) the plugs. 4130820A Fig. 3 Disconnecting the I/O Board Terminal Block Plugs 1.
- Page 5 AutoScant to MultiScan Replacement Kit 4. See Figure 4. Remove the three screws that secure the AutoScan control-end frame to the unit and remove the frame from the unit. Save the screws for later use. 4130845A Fig. 4 Removing the AutoScan Control-End Frame Installing the MultiScan I/O Follow this procedure to install the MultiScan I/O board.
- Page 6 2. I/O board-and-bracket assembly 4. Ground wire 4. Install the I/O board cardboard shield on the underside of the electrical cabinet lid using the two blind rivets. E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98...
- Page 7 Secure the lug (3) to the ground stud with the nut (1) and lock washer (2). 5. Connect ground wire G9 (4) from the main ground stud to the slide tray ground stud. E 1998 Nordson Corporation 303 866A Manual 57-41 All rights reserved...
-
Page 8: Connecting Ground Wires
Fig. 6 Building up the Slide Tray Ground Stud 1. Nut 4. Ground wire G9 7. Ground stud 2. Lock washer 5. Ground tag 8. Ground wire G11 3. Lug 6. Slide tray E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98... - Page 9 J1 connector on each hose/gun control board (2). You may need to loosen the hose/gun boards to make the connection. 7. Connect the tank ribbon cable (4) to J2 on the display board (3). E 1998 Nordson Corporation 303 866A Manual 57-41...
- Page 10 7. Motor control board 2. Hose/gun board (1 of 3) 5. Main control board 8. Motor control ribbon cable 3. Display board 6. Power harness 9. Pressure control ribbon cable E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98...
- Page 11 1. Connect the I/O board ribbon cable to XP6 on the main control board. 2. Remove the AutoScan I/O board wires, one at a time, from the XT1 terminal block plugs and connect them to the MultiScan I/O board and control system as shown in Table 1.
- Page 12 AutoScant to MultiScan Replacement Kit AutoScan I/O Board XT1 Terminal On most AutoScan I/O boards, Corresponding MultiScan Block Position this position was… I/O Board Position Not used I/O board, TB2, position 11 (manual mode input) 21 and 22 Not used...
- Page 13 Install the ferrites (1) as close to the wiring (2) unit base (3) as possible. ACTUAL SIZE 4130824A Fig. 8 Round Ferrite (1.41-in.) Installation 1. Ferrite 2. Incoming power cable/wiring 3. Unit base E 1998 Nordson Corporation 303 866A Manual 57-41 All rights reserved Issued 12/98...
- Page 14 ACTUAL SIZE 4130825A Fig. 9 Rectangular (24-Position) Ferrite Installation 1. Ferrite 3. Hose/gun ribbon cable (1 of 3) 4. Tank ribbon cable 2. Electrical tape E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98...
- Page 15 XT1 on the knockout as possible. main control board ACTUAL SIZE 4130826A Fig. 10 Square Ferrite (7-mm diameter) Installation 1. Jacketed encoder wiring 2. Drain wire E 1998 Nordson Corporation 303 866A Manual 57-41 All rights reserved Issued 12/98...
- Page 16 (except the ground wire) to TB1. Customer’s wiring to the I/O board Install the ferrites as close to the knockout as possible. ACTUAL SIZE 4130827A Fig. 11 Cable Clamp Ferrite Installation E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98...
- Page 17 3. Reinstall the electrical cabinet lid. 4. Refer to the unit manual included in the kit for information on operating the MultiScan control system. E 1998 Nordson Corporation 303 866A Manual 57-41 All rights reserved Issued 12/98...
- Page 18 AutoScant to MultiScan Replacement Kit To order parts, contact the Nordson Customer Service Center or your 3. Parts local Nordson representative. Use the following parts list to describe and locate parts correctly. Item Part Description Quantity Note — 330 055 Service kit, MultiScan for AutoScan —...
- Page 19 AutoScant to MultiScan Replacement Kit 4130828A Fig. 12 AutoScan to MultiScan Replacement Kit Parts Original copyright date 1998. MultiScan and the Nordson logo are registered trademarks of Nordson Corporation. AutoScan is a trademark of Nordson Corporation. E 1998 Nordson Corporation 303 866A...
- Page 20 AutoScant to MultiScan Replacement Kit E 1998 Nordson Corporation Manual 57-41 303 866A All rights reserved Issued 12/98...