Trigon Miniguard HF-2 Installation And Operational Instructions
  1. Manuals
  2. Brands
  3. Trigon Manuals
  4. Intercom System
  5. Miniguard HF-2 Series
  6. Installation and operational instructions

Trigon Miniguard HF-2 Installation And Operational Instructions

Handsfree telephone entry autodialer
Hide thumbs Also See for Miniguard HF-2:
Table of Contents

Advertisement

Quick Links

Download this manual
Miniguard HF-2 with Prox Reader
or
TELEPROX
Handsfree Telephone Entry Autodialer
INSTALLATION
and
OPERATIONAL INSTRUCTIONS
255 Glider Circle • Corona, CA 92880
(951) 371-1730 • Facsimile (951) 371-2592
www.TrigonElectronics.com
July 22, 2008

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Miniguard HF-2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Trigon Miniguard HF-2

Summary of Contents for Trigon Miniguard HF-2

  • Page 1 Miniguard HF-2 with Prox Reader TELEPROX Handsfree Telephone Entry Autodialer INSTALLATION OPERATIONAL INSTRUCTIONS 255 Glider Circle • Corona, CA 92880 (951) 371-1730 • Facsimile (951) 371-2592 www.TrigonElectronics.com July 22, 2008...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION ..................PRODUCT OVERVIEW ................MOUNTING ....................WIRING ..................... WIRING DIAGRAM ................SYSTEM SETUP Entering Program Mode ................Setting Setup Codes ................Setting the Relay Duration Timer ............Setting Incoming Ring Count ..............

  • Page 3: Introduction

    This manual contains all the information required to after the initial installation, you may find the TABLE OF install and program the TRIGON MINIGUARD HF-2 CONTENTS useful in locating the particular with proximity reader and the TELEPROX. If you are programming procedure you need.

  • Page 4: Mounting

    Use 600V insulated wire for this installation. 2. Do not power any other device from the Trigon’s 7. Isolate the Telco phoneline from 12 VAC power 12 VAC transformer. If a substitute transformer is wires.

  • Page 5: Wiring Diagram

    WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM Relay #2 Second Relay is Standard 5 AMP on HF-2, HS-2, M GIID Relay 100BD, MP4000 Second Relay is Optional on MGII, 100B, Minipak, NO C T.A.C. 500,1000,1500 Microprocessor relay 2 Spkr Play Microphone...

  • Page 6: System Setup

    PROGRAMMING INFORMATION PROGRAMMING INFORMATION PROGRAMMING INFORMATION PROGRAMMING INFORMATION PROGRAMMING INFORMATION Fifth Auto dial Number (16 digit max) General Programming Information __ __ __ __ __ __ __ __ __ __ __ __ The "Initial Setup" for the HF-2 with proximity reader has been programmed at the factory.

  • Page 7: Setting Call Legnth

    1. Unit must be in Program Mode. General Programming Information: 2. Press '7' then press '0' to set unit for standard The "Initial Setup" for the Miniguard HF-2 with mode. proximity reader has been programmed at the factory. 3. If desired, exit Program Mode by pressing '#' The programming of the unit focuses on the progam 4.

  • Page 8: Deleting Autodialed Telephone Number

    This procedure allows selective or complete deletion of Note: If you wish to change an existing telephone all data in the Miniguard HF-2's memory. Also, it is number, use the instructions for Adding Telephone possible to reset the Miniguard HF-2 back to its factory Numbers and enter the new number in place of the old defaults (presets).

  • Page 9: Recording New Voice Message

    PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. (J) Recording a new voice message. (L) Auto Message Control options: To change the voice message on the voice chip 1. The unit must be in Program Mode. follow these steps: 2.

  • Page 10: Operation

    OPERATION OPERATION OPERATION OPERATION OPERATION 3. To Terminate the Call, press '7'. STANDARD MODE Note: The unit will beep twice to warn of auto-call When a CALL button is pressed, the HF-2 dials a pre- termination in 10 seconds. programmed phone number and monitors the line for 4.

  • Page 11: General

    CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING General Data between [ ] is a mandatory program key stroke sequence. Data between { } is to be supplied by the programmer. Unit responses are shown between ( ).
  • Page 12 Page 12...

Table of Contents