Trigon Miniguard HF-2 Series Installation And Operational Instructions

Handsfree telephone entry autodialer

Advertisement

Quick Links

Miniguard HF-2 Series
Handsfree Telephone Entry Autodialer
OPERATIONAL INSTRUCTIONS
(Firmware revision #041215 Rev. C HF2X PWR2)
255 GLIDER CIRCLE• CORONA, CA 92880
(951) 371-1730 • Facsimile (951) 371-2592
INSTALLATION
and
with 10 number rollover
October 15, 2005

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Miniguard HF-2 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Trigon Miniguard HF-2 Series

  • Page 1 Miniguard HF-2 Series Handsfree Telephone Entry Autodialer INSTALLATION OPERATIONAL INSTRUCTIONS (Firmware revision #041215 Rev. C HF2X PWR2) with 10 number rollover 255 GLIDER CIRCLE• CORONA, CA 92880 (951) 371-1730 • Facsimile (951) 371-2592 October 15, 2005...
  • Page 2: Table Of Contents

    MINIGUARD HF-2 TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION ..................PRODUCT OVERVIEW ................MOUNTING ....................WIRING ..................... WIRING DIAGRAM ................PROGRAMMING Entering Program Mode ................Setting Operational Modes ..............Entering Autodialed Telephone Numbers ..........Verifying Autodialed Telephone Number ..........
  • Page 3: Introduction

    PRODUCT OVERVIEW PRODUCT OVERVIEW PRODUCT OVERVIEW PRODUCT OVERVIEW The TRIGON HF-2 is a multi-number auto dialer. Upon pressing the button, the HF-2 dials a programmed Power Cabling - telephone number. If the number dialed is busy or does Shielded or Twisted,...
  • Page 4: Mounting

    Use 600V insulated wire for this installation. 2. Do not power any other device from the Trigon’s 7. Isolate the Telco phoneline from 12 VAC power 12 VAC transformer. If a substitute transformer is wires.
  • Page 5: Wiring Diagram

    MINIGUARD HF-2 WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM RS-232 Printer ALARM SHUNT 1/4 Amp RELAY; Busy MICROPROCESSOR CARD READER MICROPHONE (HF-2) MEMORY SPEAKER (HF-2) AUDIO MOUTH SPEAKER PRIMARY EARPHONE RELAY VOLUME 5 Amp MAX EARTH GROUND TELEPHONE LINE INPUT Telephone line cabling...
  • Page 6: Programming

    Trigon Tech Service. Have the unit's phone number 1. Unit must be in Program Mode. ready. Trigon can call the unit and send a special 2. Press '2' then '1' (wait for tone) and enter the command tone sequence that will reset the phone to 9753.
  • Page 7: Setting The Site Id Number

    MINIGUARD HF-2 PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. PROGRAMMING, Cont. (D Verifying Telephone Numbers: (D Verifying Telephone Numbers: (D Verifying Telephone Numbers: (D Verifying Telephone Numbers: (D Verifying Telephone Numbers: (H Setting Incoming Ring Count: (H Setting Incoming Ring Count: (H Setting Incoming Ring Count: (H Setting Incoming Ring Count: (H Setting Incoming Ring Count:...
  • Page 8: Optional Voice Location Module

    (L Optional voice location module: The voice location module is an optional device that can be used instead of the Trigon Decoder and the site ID code. The module will insert a voice message at the detection of a voiced answer.
  • Page 9: Operation

    MINIGUARD HF-2 OPERATION OPERATION OPERATION OPERATION OPERATION STANDARD MODE STANDARD MODE STANDARD MODE STANDARD MODE STANDARD MODE Note: If the wrong Program code is entered, the unit will immediately hang up. If the program code or other When a CALL button is pressed, the HF-2 dials a pre- information is not entered completely, the HF-2 will programmed phone number and monitors the line for time-out and hang up.
  • Page 10: Trouble Shooting Guide

    MINIGUARD HF-2 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE NO DIAL TONE NO DIAL TONE LOSES MEMORY LOSES MEMORY NO DIAL TONE NO DIAL TONE NO DIAL TONE LOSES MEMORY LOSES MEMORY LOSES MEMORY 1.
  • Page 11: General

    MINIGUARD HF-2 CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING CONDENSED GUIDE TO USE and PROGRAMMING General Data between [ ] is a mandatory program key stroke sequence. Data between { } is to be supplied by the programmer. Unit responses are shown between ( ).
  • Page 12: Kit Wiring Diagram

    MINIGUARD HF-2 HF-2 KIT Wiring Black - Speaker Red - Speaker Yellow - Telco White - Call Btn Yellow - Telco White - Call Btn Blue - Ground Brown - 12VAC Brown - 12VAC Black - LED Violet - Relay(primary) Red - LED Violet - Relay(primary) Green - Mic...

Table of Contents