Advertisement
Quick Links
The model requires at least a six-channel radio control system
Specification
Wingspan approx.
Length excl. spinner approx.
Wing area approx.
All-up weight according to fittings approx.
Longitudinal dihedral
CG approx.
Caution: This model is not a toy!
If you are a beginner to this type of powered model, please ask an experienced model
flyer for help and support. If you attempt to operate the model without knowing what you
are doing, you could easily injure yourself or somebody else. Please keep your safety
and well-being in mind at all times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through
these instructions and check that all the kit components are actually present. We have
taken great trouble to keep construction as simple as possible, without making any
compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in
weather conditions (temperature, humidity etc.); in rare cases you may even find a slight
warp in a component. These minor faults are in the nature of film-covered built-up
wooden structures, and can easily be corrected using a heat gun, as commonly used for
modelling.
Creases:
Blow warm air over the area and rub down with a soft cloth.
Wing warp:
Hold the panel twisted gently in the opposite direction to the warp, and
apply warm air to remove the creases from the covering.
GRAUPNER GmbH & Co. KG
No liability for printing errors. We reserve the right to introduce modifications.
Instructions
FOCKE WULF 190 D
For glowplug motors up to 20 cc capacity
D-73230 KIRCHHEIM/TECK
1740 mm
1620 mm
63 dm²
4600 g
approx. 0.5°
115 - 125 mm aft of the
wing root leading edge
Order No.
9395
1
GERMANY
02/2007
Advertisement
Related Manuals for GRAUPNER FOCKE WULF 190 D
Summary of Contents for GRAUPNER FOCKE WULF 190 D
- Page 1 Order No. 9395 Instructions FOCKE WULF 190 D For glowplug motors up to 20 cc capacity The model requires at least a six-channel radio control system Specification Wingspan approx. 1740 mm Length excl. spinner approx. 1620 mm Wing area approx.
- Page 2 It is fundamentally essential to set the Centre of Gravity (CG) and control • surface travels correctly. Adjust the model until they are exactly correct. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors. We reserve the right to introduce modifications.
- Page 3 • become very hot when running, and stay at a high temperature for quite a while. Touching the hot parts can give you serious burns, so take care GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors. We reserve the right to introduce modifications.
- Page 4 If this does not work, pinch the fuel feed line between your fingers or pull it off the carburettor. Never try to stop the motor by grasping the flywheel, propeller or spinner! GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors.
- Page 5 Unless otherwise prescribed by binding law, the obligation of the GRAUPNER company to pay compensation, regardless of the legal argument employed, is excluded.
- Page 6 If material defects or manufacturing faults should arise in a product distributed by us in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner GmbH & Co. KG, D-73230 Kirchheim/Teck, Germany, acknowledge the obligation to correct those defects.
- Page 7 The same applies to surfaces to be painted, otherwise the paint is unlikely to adhere well. Before gluing parts to the fuselage it is essential to roughen the surfaces with fine abrasive paper and de-grease them with acetone or similar solvent, GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors.
- Page 8 Synthetic oil based glow fuel, to suit motor Fuel filter, e.g. Order No. 1650.1 Fuel tubing, e.g. Order No. 1643, for glow motors GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors. We reserve the right to introduce modifications.
- Page 9 Assembling the Focke Wulf 190 D Don’t start building the model until you have read right through the building instructions and are familiar with all the model’s components. If you are not satisfied with any part, inform your supplier before you start work on the model.
- Page 10 Remove the motor, drill the holes for the retaining screws at the marked points, and fix the motor to the mount. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors.
- Page 11 Assembling the wing Mark the centreline on the wing joiner, and glue it in one wing panel using plenty of GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors.
- Page 12 Apply a drop of UHU thread-lock fluid to the two grubscrews to prevent them working loose. GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY No liability for printing errors. We reserve the right to introduce modifications.
- Page 13 Assembling the FOCKE WULF 190 D To make it easier to connect the aileron, flap and retract servos to the receiver, we recommend that you connect a 100 mm extension lead to each of the appropriate receiver sockets.
- Page 14 We recommend a two-position switch for the retractable undercarriage. We wish you every success and many enjoyable flights with your FOCKE WULF 190 D. Yours - the Graupner team GRAUPNER GmbH & Co. KG...
Need help?
Do you have a question about the FOCKE WULF 190 D and is the answer not in the manual?
Questions and answers