Philips VES15.1HE LA Service Manual page 16

EN 16 4. VES15.1HE LA
4.3.3 Speakers
1. Unplug the connector from SSB.
2. Release the cables from their clamps. (if any)
3. Release the tapes which fixate the cabling. (if any)
4. Take the speakers out.
When defective, replace the both units.
4.3.4 Power Supply Unit (PSU)
Caution: It is mandatory to remount all different screws at their
original position during re-assembly. Failure to do so may result
in damaging the PSU.
1. Release the Power board cables from their clamps.
2. Unplug all other connectors from the PSU.
3. Remove all fixation screws from the PSU.
4. Separate the connection from the SSB, as it is not
unplug-able at the PSU itself (soldered connector).
5. The PSU can be taken out of the set now.
4.3.5 Power Supply Unit (PSU) (40")
Caution: it is mandatory to remount all different screws at their
original position during re-assembly. Failure to do so may result
in damaging the PSU.
1. Release the Power board cables from their clamps.
2. Unplug power connectors from the SSB, as it is not
unplug-able at the PSU itself (soldered connector).
3. Unplug all other connectors from the PSU.
4. Remove all fixation screws from the PSU.
5. The PSU can be taken out of the set now.
4.3.6 Small Signal Board (SSB)
Caution: It is mandatory to remount all different screws at their
original position during re-assembly. Failure to do so may result
in damaging the SSB.
1. Pull the upper part of the connector on the SSB, which fixes
the LVDS cable, from both sides up a little bit to release the
LVDS cable. Pull it out slowly.
Caution: Be careful, as these are very fragile connectors!
2. Release the clamps and unplug all other connectors.
3. Remove all other fixation screws from the SSB.
4. Separate the connection from the PSU.
5. The SSB can be taken out of the set now.
4.3.7 Small Signal Board (SSB) (40")
Caution: It is mandatory to remount all different screws at their
original position during re-assembly. Failure to do so may result
in damaging the SSB.
1. Release the LVDS cable from its connector on the SSB by
pressing the clips on both sides of the cable and pulling it
out slowly.
Caution: Be careful, as these are very fragile connectors!
2. Release the clamps and unplug all other connectors.
3. Remove all other fixation screws from the SSB.
4. The SSB can be taken out of the set now.
4.3.8 IR/LED Board
1. Remove the back cover as described earlier.
2. Unplug the connector that connects the board with the
SSB.
3. Release the tapes which fixate the cabling.
4. Release the board cable from its clamps.(if any)
5. Remove the screws on the cover of the board.
Remove the screws on the cover of the board and on itself.
(28", 32", 40", 48")
6. The IR/LED board can be taken out now.
When defective, replace the whole unit.
2015-Jan-20
Mechanical Instructions
4.3.9
4.3.10 LCD Panel (19")
4.3.11 LCD Panel (24")
4.3.12 LCD Panel (28", 32", 40", 48")
4.4
back to
div. table
IR/LED Board (19")
1. Remove the back cover as described earlier.
2. Unplug the connector that connects the board with the
SSB.
3. Remove the speakers as described earlier.
4. Remove the metal plate by removing the fixing tape on the
right side of the plate.
5. Remove the screw on the board.
6. The IR/LED board can be taken out now.
When defective, replace the whole unit.
1. Remove the SSB as described earlier.
2. Remove the PSU as described earlier.
3. Remove the speakers as described earlier.
4. Remove the metal plate by removing the fixing tape on the
right side of the plate.
5. Release the LVDS cable from its connector on the LCD
Panel by pressing the clips on both sides of the cable and
pulling it out slowly.
Caution: Be careful, as these are very fragile connectors!
6. Lift the LCD Panel from the bezel.
When defective, replace the whole unit.
1. Remove the SSB as described earlier.
2. Remove the PSU as described earlier.
3. Remove the speakers as described earlier.
4. Remove the IR/LED board as described earlier.
5. Remove the screws and tape that holding the plastic cover
and take it out.
6. Release the tape from the right side of the panel.
7. Release the LVDS cable from its connector on the LCD
Panel by pressing the clips on both sides of the cable and
pulling it out slowly.
Caution: Be careful, as these are very fragile connectors!
8. Release the clips that secure the LCD panel with the bezel.
9. Lift the LCD Panel from the bezel.
When defective, replace the whole unit.
1. Remove the SSB as described earlier.
2. Remove the PSU as described earlier.
3. Remove the speakers as described earlier.
4. Remove the IR/LED board as described earlier.
5. Remove the screws that holding the metal foot support and
take it out.
6. Remove the screws that holding the plastic cover and take
it out.
7. Release the tapes from left and right sides of the panel.
Release the tapes from all sides of the panel. (40")
Release the tapes from the right side of the panel. (48")
8. Pull the upper part of the connector on the LCD Panel,
which fixes the LVDS cable, from both sides up a little bit to
release the LVDS cable. Pull it out slowly.
Release the LVDS cable from its connector on the LCD
Panel by pressing the clips on both sides of the cable and
pulling it out slowly.(40", 48")
Caution: Be careful, as these are very fragile connectors!
9. Release the clips that secure the LCD panel with the bezel.
10. Lift the LCD Panel from the bezel.
When defective, replace the whole unit.
Set Re-assembly
To re-assemble the whole set, execute all processes in reverse
order.