Important Safety Instructions; Adult Supervision; First Time Setup - Philips AVENT SCD860/27 Manual

ENGLISH
Know these safety symbols
- This "bolt of lightning" indicates uninsulated material within your unit
may cause an electrical shock. For the safety of everyone in your
household, please do not remove product covering. (Fig. 1)
- The exclamation mark calls attention to features that require you to
read the enclosed user information closely to prevent operating and
maintenance problems. (Fig. 2)
Warning: To reduce the risk of fire or electric shock, this apparatus should
not be exposed to rain or moisture and objects filled with liquids, such as
vases, should not be placed on this apparatus.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Do not use the product while you are in a bathtub, shower or pool.
Immersion of the product in water could cause an electrical shock.
7 Clean only with dry cloth.
8 Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
9 Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including amplifiers) that produce heat.
10 Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use this appliance only for its intended use as described in this manual.
13 Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
14 Unplug this apparatus during lightning or when unused for long periods
of time.
15 Unplug the product immediately and do not use it if the adapter,
the cord or the product itself is damaged.
16 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped. Please check
the power cord periodically to prevent potential damages, such as
worn or cut cord. For assistance, visit our website www.philips.com/
support or contact the Philips Consumer Care Center in your country.
You find its contact details in the worldwide guarantee leaflet.
17 Keep screws and small items out of the reach of the baby.
18 All the required markings are located on the bottom of the apparatus
and on the adapter.
- WARNING: STRANGULATION HAZARD. Children have
STRANGLED in cords. Keep this cord out of the reach of
children (more than 3.5 feet (1 meter) away). Do not remove
the tag (Fig. 3).
Caution
Caution: Prevent risk of explosion, electric shock, short circuit,
or leakage
- The apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the apparatus.
- To prevent electric shock, do not open the housing of the product.
- Where the power plug is used as the disconnect device, the disconnect
device shall remain readily operable.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- Use the supplied adapter to connect the apparatus to the power outlet.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- For the adapter type, please refer to chapter 'Replacement' for details.

Adult supervision

- This baby monitor is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used as such.
- Never place the baby monitor inside or directly over the baby bed or playpen.
- To prevent overheating, do not cover the baby monitor with a towel,
blanket or any other items.
- For their safety, do not allow children to touch and play with the baby
monitor, the adapter and the accessories. THIS IS NOT A TOY.
Introduction
Congratulations on your purchase and welcome to Philips Avent! To benefit
fully from the support that Philips Avent offers, register your product at
www.philips.com/welcome.
This short manual contains important information about your uGrow baby
monitor and offers brief instructions on how to set up the baby monitor
and the app. For more detailed information and the complete user manual,
please visit www.philips.com/ugrow.
Product overview (Fig. 4)
1 WiFi status light
2 Infrared lights
3 Baby monitor lens
4 Microphone
5 Viewing indicator
6 Nightlight
7 Foot
8 Nightlight button
9 Lullaby play/pause button
10 Light sensor
11 Temperature and humidity sensor unit
12 Appliance plug socket
13 Reset button
14 On/off button
15 Wall mounting bracket
16 Adapter
17 Appliance plug
First-time setup
Before you start the set-up procedure, make sure:
- You have wireless Internet access (2.4 GHz WiFi).
- You are close enough to the WiFi router to have a good WiFi signal.
- If you use a WiFi repeater, make sure that your router and your WiFi
repeater have the same SSID and that you use the same password for
the router and the repeater.
- You have the password of your WiFi network at hand. Always connect the
baby monitor to a secure network (see chapter 'Security and privacy' in
the user manual available online at www.philips.com/ugrow).
- Make sure that your smart device runs on iOS 7 or higher, or Android
4.1 or higher.
Download the Philips Avent uGrow Smart Monitor app from the
1
App Store or Google Play. Use keywords 'uGrow smart monitor'
or 'Philips smart monitor' to find the app.
Launch the app.
2
Follow the set-up instructions in the app.
3
Mounting the baby monitor on the wall
The baby monitor comes with a wall mounting bracket. Before you mount
the baby monitor on the wall, make sure there is a good WiFi signal at the
point where you want to mount the baby monitor. Follow the instructions
below to fasten the wall mounting bracket to the wall and to attach the
baby monitor onto the wall mounting bracket.
1 Use a pencil to put a cross on the wall at the place where you want to
mount the baby monitor. (Fig. 5)
2 Hold the wall mounting bracket to the wall. Make sure that one of the
holes is right over the cross that you put on the wall at step 1.
Note: Make sure that the ring of the wall mounting bracket slants downward
when you hold it to the wall. If the ring of the wall mounting bracket slants
upward, turn the wall mounting bracket the other way around so that it is in
the correct position (Fig. 6).
3 Use a pencil to mark the other screw hole on the wall (Fig. 7).
4 Drill 2 holes in the wall at the marks (Fig. 8).
5 Use 2 screws to fasten the wall mounting bracket to the wall. Tighten
the screws with a screwdriver (Fig. 9).
6 Pass the humidity and temperature sensor unit through the hole in the
wall mounting bracket. Then align the slots in the foot of the baby monitor
with the projections on the ring. Fit the groove in the foot of the baby
monitor onto the raised edge on the inside of the ring (Fig. 10).
7 Turn the foot of the baby monitor clockwise to position the baby monitor
(Fig. 11).
8 Insert the appliance plug into the appliance plug socket in the
temperature and humidity sensor unit and insert the adapter into
a power outlet. Now your baby monitor is ready for use (Fig. 12).