Advertisement
Quick Links
Universal radio-control transmitter 2
GIRA
Info
Installation Instructions
Universal radio-control transmitter 2
Function
The universal radio-control transmitter can be used to
extend an existing electrical installation by the possi-
bility of transmitting 230 V control commands by ra-
dio. The transmitter can be operated for switching,
dimming or blind/shutter control functions.
When mains voltage (AC 230 V~) is applied to inputs
(E1, E2), the universal radio-control transmitter trans-
mits radio telegrams which are evaluated by all radio-
control receivers.
For selection and indication of the mode of operation,
the device is equipped with a pushbutton
LED
.
The universal radio-control transmitter has 4 modes
of operation:
Mode A: 2-channel dimming (toggling) (E1 and E2)
Mode B: 2-channel switching (E1 and E2)
Mode C: 1-channel dimming (E1/E2)
Mode D: 1-channel blind/shutter (E1/E2)
i
Further info
For commisssioning please read also the following
chapters, especially "Programming of radio-control
receivers".
Fitting
Install the universal radio-control transmitter
deep flushmounting box
insert
(60 mm-deep mounting box recommended).
Important
When installed outside flush-mounting boxes, the de-
vice must be sufficiently protected against shock haz-
ards by installing it, for instance, in a surface-mounted
distribution box.
Antenna
For maximum transmission range, the antenna
should be stretched out to full length and not be left
coiled up. Keep away as far as possible from large
metal surfaces such as metallic door frames.
Universal radio-control transmitter 2
and an
in a
behind a flush-mounting
A)
E2
E1
GY
BN
GY
BN
BU
BK
Safety Instructions
Attention: Electrical equipment must be installed
and fitted by qualified electricians only.
Do not connect motors in parallel with the uni-
versal radiocontrol transmitter.
Do not shorten or lengthen the antenna and do not
strip off the insulation.
B)
N
L
2/06
Order no.: 0521 00
Antenne
N
L
BU
BK
Page 1 of 5
Advertisement
Related Manuals for Gira Universal radio-control transmitter 2
Summary of Contents for Gira Universal radio-control transmitter 2
- Page 1 Universal radio-control transmitter 2 GIRA Info Installation Instructions Universal radio-control transmitter 2 Order no.: 0521 00 Function The universal radio-control transmitter can be used to extend an existing electrical installation by the possi- bility of transmitting 230 V control commands by ra- dio.
-
Page 2: Installation And Adjustment
Universal radio-control transmitter 2 GIRA Info Installation Instructions Installation and adjustment Depending on wiring and on the selected mode of operation, the universal radio-control transmitter transmits radio telegrams, e.g.: „channel 1 = switch on“. Antenne Connect the wires as follows:... - Page 3 Universal radio-control transmitter 2 GIRA Info Installation Instructions Connection of conventional pushbuttons (n.o. con- Important: Switching over (toggling) of the telegram type (on/off, tacts): brighter/darker) is effected in the transmitter. When a Actuation: T1 < 1s: switch on receiver has been operated locally or by another T1 >...
-
Page 4: Programming Of Radio-Control Receivers
Universal radio-control transmitter 2 GIRA Info Installation Instructions Programming of radio-control receivers A universal radio-control transmitter channel can be Procedure programmed into an unlimited number of radio recei- 1. Switch the radio-control receiver into the program- vers. Programming information is stored only in the ming mode (see „Radio-control receiver“... -
Page 5: Specifications
R&TTE Directive communication networks must comply with nation- (1999/5/EC). The complete declaration of conform- al legislation. ity can be found in the Internet under: www.gira.de/ • This radio system must not be used for communi- konformitaet. cation beyond property boundaries.