repairs. The machine is to be unplugged from the mains before opening. Contens Live parts inside the machine may still be live for some time after unplug- ging from the mains. Page NOTE ! Covering or parts that are capable of being removed Declaration of conformity from the unit without accessory equipment have to be reat- Guarantee...
The original IKA ® cable layout must be restored following servicing! If the target value of the speed is changed too rapidly, the machine (HS/KS 260 basic) will turn itself off automatically.
device is ready to operate after plugging in the mains plug. If these Useful facts procedures are not followed, safe operation cannot be guaranteed and/or the equipment may be damaged. With the purchase of this device, you have acquired a high-quality Observe the ambient conditions (temperature, humidity, etc.) listed product.
Description of the LCD-Display - HS/KS 260 control Display Real value Rated value Description of the LED-Display - HS/KS 260 basic Display element for the setting speed Mot 1/min 50 100 150 200 250 300 350 400 450 500 On Off Time min Display element for Continuous...
Page 6
back on, both functions must be started again. The upper speed limit d.) If the upper speed limit is fixed, the unit 1/min in the left display can only be set or changed in operating mode A. You can recognice changes to OK.
Page 7
the display for operating mode B along with * in the right display. d.) The new speed target value has been set or just stored in the left After the power has been turned off,the device will no longer auto- display (for example 130) is the shown in the unit 1/min and flashing matically start up in operating mode B by itself.
Page 8
a.) All display elements in the digital displays are activated for about 2 on the display. In addition, the text is shown on the display seconds. instead of SV . The actual value of the time setting must be understood from this point onward as the time remaining for the agitation process.
ATTENTION! After a power failure, the unlocked Note: If the time expiration signal has been activated, expiration of the (freely movable) agitation table will continue to perform set time is indicated by a sequence of signals (3 times 5 short tons at a circular motion until the lock function can fasten the intervals of about 10 seconds).
Control model tion or for several agitation processes in timed mode. 3 4 5 9 5 9 . 9 5 9 : The amount 3 4 5 NOTE: After the power has failed, the set time is erased and the of time requi- device switches into Offline operating mode (standstill).
410 x 33 x 370 ® Attachments recommended by IKA must be connected to the agita- ATTENTION! The dish attachment is secured in place by four lateral tion table to ensure safe and secure operation. in addition , the usable clamping screws on the agitation table.
AS 260.1 Universal attachment Error code Error Cause of the error AS 260.5 Separating funnel attachment Off - LED (red) The potentiometer for -Too rapid a change in the the speed is not assig- speed target value 1x flash / ning any target value -Internal device error 2 sec pause...
Control error codes: Interface and outputs ATTENTION! If an error code is encountered, an audio warning signal is generated and the red Off signal light goes on in the display (HS/KS 260 control version only) field. First, please try to continue operating by turning the device off The HS/KS 260 control is equipped with a 15-pin SUB-D connector on the rear and back on again.
Page 14
NAMUR Instructions Function Display • RTS: (Pin 7) LOW (positive tension) additional / PC may send • RTS: (Pin 7) HIGH (negative tension) IN_PV_X Reading the real-value / PC may not send OUT_SP_Xn Setting the actual value to n • CTS: (Pin 8) LOW (positive tension) up to a maximum of the set / PC recipient...
Ending of ramp loop IN_TYPE Requiring identification of (HS/KS 260 control version only) laboratory instrument ® PC 5.1 Adapter IKA - Control IN_NAME Requiring the designation name The Adaptor PC 5.1 splits the analog and serial signals. The analog OUT_NAME...
(25-pin plug). only cleansing agents which have been appro- ved by IKA ® to clean IKA ® devices. To remove use: AK 2.1 Cable Dyes isopropyl alcohol This cable is required to connect the 7-pin connector to a chart recor-...
AS 260.5 Separating funnel attachment 8,8 (control) STICKMAX Adhesive mat HS/KS 260 basic (HS/KS 260 control version only) Speed setting: Analog (infinitely variable) Adapter IKA ® - Control PC 5.1 Rotary knob on front side left PC 1.5 Cable Speed display: 10 LED’s with scale-in...