Advertisement
SmartCode at a Glance
Exterior
Keypad
SmartKey
tool hole
Tip: To light up the keypad
while the door is locked,
press the Lock button before
entering your user code.
The keypad will not light up
if the door is unlocked.
Status LED colors
These features can be adjusted in some smart home apps.
Color
Green (solid)
Green (blinking)
Red (solid)
Red (blinking)
Status
Blue (solid)
LED
Blue (blinking)
Amber (solid)
Amber (blinking)
Network Reset
Network Reset will delete all Bluetooth pairings, user associations,
and remove the lock from the account.
1 Press and HOLD
2 Release "A."
"A" for 10 seconds.
You will see a
You will hear 1 short
blinking amber
10s
beep and see an
LED to indicate
amber LED.
it is in network
reset mode.
Note: After 3
seconds, you will
hear 1 short beep
and see a blue
LED. You should
continue to hold "A"
to enter network
reset mode.
3 Press and release the
4 If successful, you will hear 1 long
Program button to
beep and see a green LED. If
confirm network reset.
unsuccessful, you will hear 5 rapid
beeps and see a blinking red LED. If
unsuccessful, repeat from step 1.
Successful:
Program
button
The Program button must be
green
pressed within 10 seconds of
LED
releasing "A" or the function
will time out.
Troubleshooting
A complete Aura Bluetooth Keypad
Programming and Troubleshooting Guide is available at
www.kwikset.com/aura/support
Interior (cover removed)
Lock
button
Button "A"
Status
Keyway
LED
Lock Status
Action successful
Unlocked
Door handing process unsuccessful
Action unsuccessful or incomplete
Low battery
Bluetooth Pairing successful
Bluetooth Pairing Mode
Entering Network Reset mode
Network or System Reset mode.
Action required.
Locked
System Reset
System Reset will delete all access codes and lock settings including
lock handing. The lock will run the handing process at the end of the
System Reset.
1 Press "A" 10
times. You will
hear 1 short
beep and see a
blinking amber
LED to indicate
Status
it is in system
LED
reset mode.
3 If successful, you will hear 1
long beep and see a green
LED, and the reset process
will begin. During the reset
process, the LED will blink
green/red a few times and
will beep when complete.
Unsuccessful:
If unsuccessful, you will
hear 5 rapid beeps and
see a blinking red LED. If
unsuccessful, repeat from
red
step 1.
LED
SmartKey Re-Keying
Re-key the lock to work with your existing key. See the supplied
SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the battery pack before
re-keying your lock.
Reference Guide
System Alerts
Alert
Keypad flashes red once with
one beep*.
Keypad flashes red three
Battery
times with three beeps*.
pack
Keypad flashes red 15 times
with 15 beeps*
Button "B"
Keypad flashes red with fast
beeping sound for three to
Program
four seconds.
Button
Keypad flashes red with
continuous beeping sound
for two seconds.
Turn
piece
Lock beeps continuously.
shaft
*Beeping sounds will only be heard if Lock Sounds have not been disabled in the app.
Manual Door Handing
If needed, the door handing process can be initiated manually. This is useful if the lock is being
moved to a different door.
1 Remove battery pack.
3 Press the Program button once more.
2 Press and release
the Program
button to confirm
system reset.
Program
button
Successful:
Unsuccessful:
green
LED
4 / 4
Reason
Solution
One incorrect code entered.
Re-enter code.
No user code programmed.
Program at least one user code.
Re-enter code after 60 second keypad
Three incorrect codes entered.
lockout.
Low battery.
Replace batteries.
Door jammed while attempting
Manually re-lock door. If needed,
to lock.
reposition strike.
Interior assembly is
Remove battery pack, reconnect the interior
disconnected from exterior.
to the exterior, then reinstall battery pack.
2 Press and HOLD
the Program button
while reinserting
the battery pack.
Release the
Program button
after 3 seconds.
The status LED will
flash red and green.
4 The latch bolt will extend and retract to
learn the orientation of the door. The LED
will flash green if handing is successful
or red if handing is unsuccessful.
Factory Reset
Factory Reset will delete all Bluetooth pairings, user associations,
remove the lock from the account and reset all lock settings
including handing.
1 Remove
2 Press and HOLD
battery pack.
the Program button
while reinserting
the battery pack.
Keep holding
the button for
30 seconds until
the lock beeps
and the status
LED flashes red.
3 Press the Program button
once more. The LED will
flash green and red, and
the auto-handing process
will begin.
red
LED
Important Safeguards
1.
Read all instructions in their entirety.
2. Familiarize yourself with all warning
and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes.
5. Dispose of used batteries according to local laws and
regulations.
WARNING: This Manufacturer advises that no lock
can provide complete security by itself. This lock may
be defeated by forcible or technical means, or evaded
by entry elsewhere on the property. No lock can
substitute for caution, awareness of your environment,
and common sense. Builder's hardware is available in
multiple performance grades to suit the application.
In order to enhance security and reduce risk, you
should consult a qualified locksmith or other security
professional.
Status
LED
Status
LED
4 The latch will retract and
extend to learn the orientation
of the door. The LED will
flash green if auto-handing
is successful or red if auto-
handing is unsuccessful.
© 2019 Spectrum Brands, Inc.
Advertisement
