Subscribe to Our Youtube Channel
Related Manuals for Lamona LAM2601
Summary of Contents for Lamona LAM2601
- Page 1 Circular Island Extractor LAM2601 Instructions and Installation www.howdens.com/appliance-registration...
- Page 2 See back page for product serial number...
-
Page 3: Table Of Contents
Contents Page Environmental note IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood Dimensions Specifications Optional extras Using your cooker hood Before first use To use your cooker hood Cleaning your cooker hood The grease filter Maintenance 11 – 14 Removing and cleaning the grease filter Changing a light bulb Fitting the carbon filters... -
Page 4: Environmental Note
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Service Line. IMPORTANT: Any installation work must be carried qualified electrician... - Page 6 o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room.
- Page 7 o Note: Your cooker hood is designed to remove cooking odours from the room and not steam. o Warning - Always ensure that the cooker hood been disconnected from power supply before carrying out any work on the hood, including replacing lamps. o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose.
-
Page 8: Specifications Of Your Cooker Hood
Specifications of your cooker hood Hanging plate x 1 Connector pieces x 3 Angle bars x 6 Expansion bolts x 6 Wall plugs x 9 ST6 Screws x 9 M4 bolts x 36 M4 washers x 36 M4 nuts x 36 Self-tap screws x 3 PRODUCT DIMENSIONS Height:... -
Page 9: Using Your Cooker Hood
IMPORTANT: Please positioning instructions on pages 17 - 18 to obtain precise information on the height requirements for this product. If you are using the appliance in recirculation mode, then PLEASE NOTE that some of the vent in the upper chimney section must be exposed. -
Page 10: Cleaning Your Cooker Hood
o Find the control panel, which is located in the middle of the main body of the cooker hood. o There are several buttons on the control panel, which perform separate functions (see line drawing on previous page). IMPORTANT: IDEALLY YOU SHOULD SWITCH ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. -
Page 11: The Grease Filter
The grease filter o Your cooker hood is fitted with a grease filter, which helps to absorb grease particles and protect your kitchen and furniture from greasy residues. o The metallic filter may become flammable if you allow it to get saturated with greasy residues. -
Page 12: Changing A Light Bulb
Changing a lamp IMPORTANT: BEFORE ATTEMPTING TO CHANGE LAMP, MUST ENSURE THAT YOU HAVE DISCONNECTED COOKER HOOD FROM YOUR MAINS SUPPLY. o Remove the fixing screw that holds the grease filter in place and then pull away the grease filter from the cooker hood. o Use a screwdriver to remove the 6 fixing screws that hold the light board in place. -
Page 13: Fitting The Carbon Filters
o Use a screwdriver to retighten the 6 fixing screws that hold the light board in place. o Refit the grease filter once it has dried and then retighten the fixing screw that holds it in place. o If the lights still do not work, make sure that lamps... - Page 14 2) Hook the carbon filter over the pins that are located at the end of the motor. Turn carbon filter anticlockwise, until you feel it click into place. o Repeat this process second carbon filter. You need to place a carbon filter at either end of the motor.
-
Page 15: Electrical Connection
Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION. o The cooker hood’s power cable must be fitted upstream from the electrical connection, using a dual pole fused spur outlet switch with a contact distance of at least 3 mm. THE FUSE MUST BE RATED AT 3 AMPS. -
Page 16: Before Beginning Installation
Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area. In addition check whether there is an electrical socket available that will be accessible once the hood is mounted. If the product is going to be used in extraction mode, then there should also be space to connect a ducting hose to the outside. -
Page 17: Positioning
Positioning Height of the appliance Total height of the kitchen Height of the worktop Distance between the worktop and the hood 7 cm = Height of the hood canopy o To work out the height of the appliance, you need to use the following formula: X = A –... -
Page 18: Installing Your Cooker Hood
If you are using the appliance in recirculation mode, then PLEASE NOTE that some of the vent in the upper chimney section must be exposed. You will have to take this into account when calculating the minimum height of the cooker hood when installed. -
Page 19: Supplied Installation Components
Fixing the cooker hood to the ceiling 1) Position the hanging plate on the ceiling and then mark the position of the screw holes. o If you are going to be using the hood in extraction mode, then you should also mark the position of the larger hole in the centre hanging plate. - Page 20 2) Extend the angle bars to the required height, then fix them in position using the 10 mm x M4 nuts and bolts with metal washers (12 pcs) (as shown in the line drawing opposite). o IMPORTANT: The angle bars must have an overlap of AT LEAST 100 mm.
- Page 21 4) Locate the holes on the top of the main body of the cooker hood that you fix the connector pieces and angle bars to. o The positions of the holes are indicated in the line drawing opposite. 5) Use the 10 mm x M4 nuts and bolts with metal washers (6 pcs) to secure the main body of the hood to the angle bars.
- Page 22 5) Lift the main body of the cooker hood towards the hanging plate. o If you are going to be using the hood in extraction mode, you should feed the ducting hose through the hole in the ceiling that you made in step 1.
-
Page 23: Completing The Installation
Completing the installation o The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The appliance should now be connected to the electrical supply. See page 16 for detailed information on the electrical connection. -
Page 24: Troubleshooting
o Connect the spigot to the top of the cooker hood, and then connect a 125 mm ducting hose to the spigot (please note that the ducting hose is not supplied with the appliance). o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours. - Page 25 My cooker hood has switched off during operation. o The safety cut-out device has been tripped. o Turn off the hob and then wait for the safety cut-out device to reset. o IMPORTANT: If you have installed your cooker hood too low, the safety cut-out device will frequently trip.
- Page 27 Call the Depot number on your Proof of Purchase Document supplied with the product / kitchen. Call the LAMONA Service Line on 0344 460 0006 *Product installed within a domestic kitchen or a non-domestic kitchen where 8 or fewer people are using the appliance.
- Page 28 Product serial number (Place sticker here) ISSUE v4 280917...
Need help?
Do you have a question about the LAM2601 and is the answer not in the manual?
Questions and answers