Advertisement
GENERAL SAFETY CONTINUED:
DO NOT use this product to perform a task for which it has
7
not been designed.
DO NOT deface the certification plate attached to the
7
compressor tank.
DO NOT cover the compressor or restrict air flow around the
7
unit whilst operating.
DANGER! DO NOT direct the output jet of air towards
q
people or animals.
DO NOT operate the compressor without an air filter.
7
DO NOT allow anyone to operate the compressor unless
7
they have received full instructions.
WARNING! the air tank is a pressure vessel and the
following safety measures apply:
DO NOT tamper with the safety valve, DO NOT modify or alter
7
the tank in any way and DO NOT strap anything to the tank.
DO NOT subject the tank to impact, vibration or to heat and
7
DO NOT allow contact with abrasives or corrosives.
drain condensation from tank and inspect inside walls for
3
corrosion as per the maintenance schedule and have a
detailed tank inspection carried out annually. the tank shell
must not fall below the certified thickness at any point.
WARNING! If an electrical fuse blows, ensure it is replaced
with an identical fuse type and rating.
When not in use for a prolonged period, and if possible, store
3
the compressor carefully in a safe, dry, childproof location.
When the compressor is not in use, it should be switched off,
3
isolated from the mains supply and the air drained from the
tank.
2. INTRODUCTION & SPECIFICATIONS
2.1.
INTRODUCTION.
High output units suitable for the professional workshop. Both units
are fitted with two genuine 3hp motors and two identical pumps. twin
capacitors and a centrifugal switch aid trouble free starting on a 230V
32A supply. they are supplied with a control box that allows stepped
start up. Pumps feature heavy-duty full cast cylinders capped by
alloy heads for improved heat dissipation and long life. Heavy-duty
drive guards protect belt and flywheel that is designed to force air
over the pump to aid cooling. supplied with full ce certification and
test certificates.
2.2.
SPECIFICATIONS
Model: ........................................... SAC1276B ...............SAC2276B
Motor output (HP): ......................................2x3 ........................... 2x3
Voltage / Phase: .................................... 230V/1 ..................... 230V/1
Input current: .............................................. 32A ...........................32A
speed (rpm): .............................................1636 .........................1280
Air displacement (cfm/lm): .................26.8/759 ......................30/850
Max free Air delivery (cfm/lm): ..........19.4/549 ...................21.8/618
Max Pressure (psi/bar): ..........................145/10 ......................145/10
tank capacity (l): .......................................270 ...........................270
dimensions (WxdxH) (mm): ...... 1550x540x935 ......... 1550x540x960
net Weight (kg): ..........................................138 ...........................150
noise (dB.A): .................................................77 .............................77
noise lwA (dB.A): .........................................97 .............................97
3. PREPARATION
3.1.
remove compressor from packaging and inspect for any
shortages or damage. If anything is found to be missing or
damaged, contact your supplier.
3.2.
save the packing material for future transportation of the
compressor. It is recommended that the packing is stored in a
safe location, at least for the period of the guarantee. then, if
necessary, it will be easier to send the compressor to the
service centre.
3.3.
confirm that the mains voltage corresponds with the voltage
shown on the compressor data plate. fit a suitable 3 pin
industrial plug - see section 1.1.10. of the safety Instructions.
3.4.
take care to transport the compressor correctly, DO NOT
overturn it or lift it with hooks or ropes.
3.5.
fit the 4 rubber anti-vibration supports (fig.3), raise the
compressor using a suitable pallet truck or fork lift and push
the supports into the base of each foot.
3.6.
Position the compressor on a flat surface or with a maximum
permissible inclination of 10° (fig.1). Site in a well ventilated
area, protected against atmospheric pollution and not in a
place subject to explosion hazard. If the surface is inclined and
smooth, check if the compressor moves whilst in operation.
If the surface is in a raised position, make sure the compressor
cannot fall, securing it in a suitable way.
3.7.
To ensure good ventilation and efficient cooling, the compressor's
belt guard must be at least 100cm from any wall (fig.2).
3.8.
remove the plastic transit plug from the oil filler hole (figs.4 & 5)
and replace it with the filler/breather plug. It is a push fit,
ensure that it is pushed fully home.
3.9.
Before using the compressor, check the oil level by observing
the sight glass as shown in figs.4 & 5. If the oil is not up to the
max. mark, it should be topped up with synthetic oil (see
section 5.7. for recommended oils). We do not recommend
using mineral oil in these compressors. DO NOT overfill.
fig.2
fig.1
fig.3
Original Language Version
sAc1276B, sAc2276B
Issue:2 - 20/02/12
Advertisement
