Roland Texart RT-640 Setup Manual
  1. Manuals
  2. Brands
  3. Roland Manuals
  4. Printer
  5. Texart RT-640
  6. Setup manual
Roland Texart RT-640 Setup Manual

Roland Texart RT-640 Setup Manual

Hide thumbs Also See for Texart RT-640:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Thank you very much for purchasing this product.
- To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through
this manual completely and store it in a safe location.
- Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
- The contents of this manual and the specifications of this product are subject to change without notice.
- This manual and the product have been prepared and tested as much as possible. If you find any misprint or error, please
inform us.
- Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this
product, regardless of any failure to perform on the part of this product.
- Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any
article made using this product.
Setup Guide

Advertisement

Table of Contents
loading

Related Manuals for Roland Texart RT-640

Summary of Contents for Roland Texart RT-640

  • Page 1 - This manual and the product have been prepared and tested as much as possible. If you find any misprint or error, please inform us. - Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this product, regardless of any failure to perform on the part of this product.

  • Page 3: Table Of Contents

    2. Included Items ..............................5 3. About the Symbols ............................7 4. Assembling and Installing ...........................8 Assembling and Installing ..........................8 Installing the Roland Ink System ......................... 19 5. Filling with Ink ..............................20 Filling with Ink for the First Time ......................... 20 6. Network Settings ............................32 Step 1：Make the Network Settings for the Computer ..............

  • Page 5: Installation Environment

    1. Installation Environment Deciding on an Installation Site Install in a quiet, stable location offering good operating conditions. An unsuitable location can cause accident, fire, faulty operation, or breakdown. WARNING Install the machine in a location that is level, stable, and able to bear the weight of the machine.

  • Page 6: Temperature And Humidity

    1. Installation Environment Temperature and Humidity Maintain the specified temperature and humidity even when the machine is not in use. If temperatures are too high or too low, it may cause malfunction. During operation: Temperature 18 to 25˚C (64.4 to 77 ˚F), relative humidity 35 to 65 % RH (no con- densation) During non-operation: Temperature 15 to 30˚C (59 to 86 ˚F), relative humidity 20 to 80% (no con- densation)

  • Page 7: Included Items

    2. Included Items The following items are packed together with the machine. Make sure they are all present and accounted for. Printer unit Arms (one for right and Stand legs (one for Power cord (1) Casters (2) left each) right and left each) Stand stay (1) Shafts (2) Feed adjusters (2)
  • Page 8 Read this first (1) document) (1) TENANCE GUIDE (1) * Not required when using four colors (cyan, magenta, yellow, and black). Roland Ink System Ink pouch holder (1) Subtank guard (1) Ink tube covers (bottom) Ink tube cover (top) (1)

  • Page 9: About The Symbols

    3. About the Symbols The meanings of the symbols used in this document are as follows. The symbol indicates things that must be followed in relation to operation. Always follow these instructions to prevent accident or damage due to misop- eration.

  • Page 10: Assembling And Installing

    4. Assembling and Installing Completed drawing About the picture Tighten temporarily Tighten fully Assembling and Installing WARNING Perform this task with all power switches left switched off. Otherwise sudden movement of the machine may cause injury. CAUTION Unpacking and installation must be carried out by six or more personnel. Otherwise the machine or the stand may fall, resulting in injury.
  • Page 11 4. Assembling and Installing  When tightening the bolts fully, tighten them securely. Loose bolts may cause the stand to wobble. Assemble the stand.  Place the stand stay on the stand legs with the U-shaped brackets on the inside. ...
  • Page 12 4. Assembling and Installing Check the assembly. Verify below. View from right above View as seen from the front That it is a That it is a parallel parallel Tighten the bolts fully at the four locations on the top and the four locations on the side as in and then Tighten...
  • Page 13 4. Assembling and Installing Install the casters onto the stand legs. Install to the side with the most distance from the stand stay to the end. Tighten Pipe fully Bolts (long): 8 Set the stand upright and tighten the bolts as in and then to install the arms.
  • Page 14 4. Assembling and Installing  Place the machine on the stand.  Tighten the bolts as in and then to secure the machine to the stand. Tighten fully Bolts (long): 4 Washers: 4...
  • Page 15 4. Assembling and Installing Installing the feed adjusters.  Install the feed adjuster stays as in and then Only the bolts on the left side when looking at the front of the machine are tightened fully. The bolts on the right side are tightened temporarily. Tighten Tighten temporarily...
  • Page 16 4. Assembling and Installing Install the other feed adjuster to the back of the machine. Take care to install the adjuster with the correct orientation. Tighten fully Bolts (short): 4 Underside Fully tighten the temporarily tightened bolts on the right side of the feed adjuster stay as in and then Tighten...
  • Page 17 4. Assembling and Installing Install the media holder.  Place the shafts on the stand.  Pass the shaft through the media holder (left) as in and then Pass the shaft through from the right when looking at the rear of the machine.
  • Page 18 4. Assembling and Installing Move the media holder (left) to the left side of the shaft, and attach the retaining screw. Tightening the retaining screw only lightly is sufficient. Tighten loosely In the same manner, pass the shaft through the media holder (right) as in and then...
  • Page 19 4. Assembling and Installing Attach the retaining screw. Tightening the retaining screw only lightly is sufficient. Tighten loosely Install the shaft clamps to secure the shaft. Make sure the media holder is not so close to the end of the shaft that it becomes pinched by the shaft clamp.
  • Page 20 4. Assembling and Installing Install the drain bottle.  Remove the bottom plug. Be careful as the fluid used in the inspection may still remain when removing it.  Install the drain bottle.  Turn the bottle without applying excessive force. ...

  • Page 21: Installing The Roland Ink System

     Store the retainers because they are needed again when transporting the machine. Installing the Roland Ink System About this procedure This procedure must be performed by a suitably qualified service technician. Never attempt to perform this procedure yourself.

  • Page 22: Filling With Ink

    5. Filling with Ink About the picture Direction mark ou can select settings and switch screens by pressing the cursor keys indicating directions. ENTER mark When you press [EN- TER], you can set the selected setting and execute the processing. Press MENU button once Press button several times...
  • Page 23 5. Filling with Ink  Connect both the power cord and the Ethernet cable (commercially available). Use a power plug adapter if the electrical outlet is a two-prong outlet. Never insert a Ethernet cable telephone cable. (Category 5 or higher) Ethernet (100Base-TX is recommended.)
  • Page 24 5. Filling with Ink  Lock the casters so the machine does not move.  Close the front cover.  Switch on the main power switch.
  • Page 25 5. Filling with Ink  Hold down and press the sub power switch.  When the screen on the left is displayed, select the desired language and press  Press to select the desired length unit, and press  Select the desired temperature unit in the same way, and press Select the ink type.
  • Page 26 5. Filling with Ink When the screen on the left is displayed, set the drain bottle.  Press Apply the Cleaning Liquid.  When the screen on the left is displayed, remove the right cover.  Touch the back of the operation panel to discharge any static electricity.
  • Page 27 5. Filling with Ink Verify that the screen on the left is displayed, and apply cleaning liquid to the rubber portion of the outer frame. Area to apply * Cleaning liquid will be supplied by the service technician during installation. ...
  • Page 28 5. Filling with Ink Install the subtank guard, and then affix the ink color labels.  Verify that the screen on the left is displayed, and pull the ink pouch holder towards the front of the machine.  Press When the screen on the left is displayed, insert each subtank.
  • Page 29 5. Filling with Ink When the screen on the left is displayed, follow steps to install the subtank guard. Loosen the left and right bolts slightly to make a gap. Insert the subtank guard into the gap between the bolts and the machine.
  • Page 30 In the event you install an ink pouch of the wrong color, contact your authorized Roland DG Corp. dealer.  Never touch the area around the ink filling port. Touching this area accidentally may force air into the ink path and cause a malfunction.
  • Page 31 5. Filling with Ink  When the screen on the left is displayed, raise all the ink pouch holders. Hold here  Do not let go of the ink pouch holders when lifting them. Raise the holders slowly until they click firmly into place.
  • Page 32 Attach the drain bottle, and then press When this screen appears, filling with ink is finished. After this, the next step is to adjust the feed adjusters. This procedure will be performed by a Roland DG service technician, so leave it up to them.
  • Page 33 5. Filling with Ink  For information on how to install the take-up system, refer to the take-up system user’s manual.  If using the TUC-3, it is necessary to make adjustments by removing springs and other parts from the control box and frame of the TUC-3. For details, refer to the TUC-3 User's Manual.For details, refer to TUC-3 documentation.

  • Page 34: Network Settings

    6. Network Settings Memo The examples used in the procedures for making the settings described in this section assume you are using one computer and one machine. The settings used in this section are merely example settings. The procedures and setting values described here may not be suitable for all operating environments. If the computer you're using is connected to a number of networked devices or to the Internet, incorrect settings may adversely affect the entire network.
  • Page 35 6. Network Settings  Select [Internet Protocol Version 4 (TCP/ IPv4)] and then click [Properties]. If the check box for [Internet Protocol] is unselected, then click and check the box. The [Internet Protocol Version 4(TCP/IPv4)] dialog box will appear.  Select [Use the following IP address].

  • Page 36: Step 2：Make The Network Settings On The Machine

    6. Network Settings Step 2：Make the Network Settings on the Machine Set the IP address.  Press  Press several times until the screen shown on the left appears. Press in this order.  Press three times.  [IP ADDRESS]: 192.168.000.XXX Note: Here, "XXX"...
  • Page 37 6. Network Settings  Press to select the address number. [SUBNET MASK]: 255.255.255.000 Note: For the subnet mask, make the setting the same value as the one used by the computer. Here, "255.255.255.000" is entered by way of example.  Press ...

  • Page 38: Step 3：Make The Port Settings For The Software Rip

    RIP. Confirming that a network connection has been established Roland VersaWorks You can check whether the connection to the network has been complete by using the printing-test feature. For the information on the method to conduct a printing test, refer to the documentation for the...
  • Page 40 R4-160520T...

Table of Contents