Advertisement
5. oPErAtion
dAnGEr! The press is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons,
always ensure the workpiece is secured on the worktable to ensure loads that flex will not suddenly "give" causing danger to
operator or damage to component. Ensure you have read and understood Section 1 safety instructions.
5.1
Before operating the press, purge the hydraulic system in order to eliminate any air that may have built up during transit. Open the
release valve and pump the handle several times (suggested 20 times). Should the system malfunction at any time, repeating this
process may resolve the problem. If not refer to Maintenance heading 6.3.
5.2
Place the "Vee" blocks (13) onto the worktable, then place workpiece onto the "Vee" blocks note: Care must be taken to ensure that the
"Vee" blocks do not fall from the worktable. If necessary hold the configuration in position with clamps.
5.3
Select a suitable mandrel for the task, the supplied mandrel is shown in fig.3. Ask your Sealey dealer about available mandrels. Secured
by a socket set screw with a 3mm hex socket.
5.4
Turn the control valve knob clockwise to close valve.
5.5
Pump handle to apply load to the workpiece.Observe work and gauge (fig.1). do not exceed the maximum load of 30tonne.
WArninG! do not apply off-centre loads. The position of the actuator (ram) can be adjusted laterally +/- 100mm; the "Vee" blocks will
require repositioning equally about the actuator (ram) centre line.
5.6
When the work is done, stop pumping the handle. Slowly and carefully release load from workpiece by turning control valve knob
anticlockwise, in small increments.
5.7
Once the hydraulic unit has been fully retracted, remove the workpiece from the press. note: Always keep the hydraulic unit fully
retracted after use to avoid ram corrosion.
6. MAintEnAncE
note: Maintenance and repair must only be carried out by a qualified person. Contact your Sealey dealer for details.
6.1
Always keep the press clean, dry and lubricate all moving parts at regular intervals.
6.2
When not in use the hydraulic unit must be fully retracted.
6.3
Should you need to check or replace oil, ensure the hydraulic unit is fully retracted. Remove the oil reservoir filler plug and top
up using Sealey hydraulic jack oil (Sealey Part No's: HJO500MLS/HJO5LS). do not use brake fluid. After filling, purge the system
as described in Section 5.1 to remove any air.
Parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
recycle unwanted materials instead of disposing of them as waste. All tools, accesso-
ries and packaging should be sorted, taken to a recycling centre and disposed of in a
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE PRESS.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
de-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the
product and the oil according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPortAnt: No liability is accepted for incorrect use of product.
WArrAntY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inForMAtion: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey Limited
Ø58
Supplied plain mandrel with mandrel adaption dimensions
Environmental Protection
manner which is compatible with the environment.
Sole uK distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
18
Ø22
Ø25
8
3
fig.3
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
email
YK30XF
Issue No: 2(I) - 15/04/15
Advertisement
