Advertisement
3.9
Angle Setting.
3.9.1 When the torque setting has been confirmed
the wrench will go to angle setting.
3.9.2 The last saved angle will be shown.
3.9.3 Press the
button to ZERO the figures.
3.8.4 Press the
button to change each digit in
turn, press the
digits.
3.9.5 When the angle figure is set, press the
button to confirm.
Note: If no buttons are pressed within 6 seconds
the display will return to the main screen.
Note: 'Erro' will be shown on the screen if the
angle set does not fall between 1° and
360°.
4.
OPERATION
4.1
Display Back-light.
4.1.1 Press and hold the
4.2
Torque Measurement.
4.2.1 Select the correct size socket and snap it onto
the wrench.
4.2.2 Press the
button to scroll through the
pre-set torque figures (M1-M5).
4.2.3 Place the wrench onto a nut/bolt and begin to
tighten, use a smooth motion and avoid jerky
movements.
4.3
LED and Buzzer Indicators - Torque.
4.3.1 When under 50% of the set torque, the LED
will flash GREEN.
4.3.2 After 50% of the torque figure has passed
the LED will change to a solid YELLOW.
4.3.3 5Nm (or equivalent value) from the set torque
the buzzer will sound.
4.3.4 The LED will change to RED when you are
within 2% of the set torque.
4.3.5 When the set torque is reached the buzzer will
become quicker.
4.3.6 If you go over the set torque the wrench will
emit a continuous tone and the LED will turn
back to GREEN.
4.4
Angle Measurement.
4.4.1 Press the
button to switch to angle
measurement.
4.4.2 Select the correct size socket and snap it onto
the wrench.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
button to move between
button for 5 seconds.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
4.4.3 Press the
button to scroll through the
pre-set angle figures (M1-M5).
4.4.4 Place the wrench onto a nut/bolt and begin to
tighten, use a smooth motion and avoid jerky
movements.
4.4.5 To change the direction from clockwise to
anti-clockwise press the
symbol will appear on the display.
4.5
LED and Buzzer Indicators - Angle.
4.5.1 When under 50% of the set angle, the LED
will flash GREEN.
4.5.2 After 50% of the angle figure has passed
the LED will change to a solid YELLOW.
4.5.3 The LED will change to RED when you are
within 2% of the set angle.
4.5.4 When the set torque is reached the buzzer will
emit a continuous tone.
4.5.5 If you go over of the set angle by 2% the LED
will turn back to GREEN.
4.5.6 Press the
button to ZERO the angle
for another reading. The below will display.
4.5.7 When all angle measurements are done, press
the
button to switch back to torque
measurement.
Environmental Protection.
Recycle unwanted materials instead of
disposing of them as waste. All tools,
accessories and packaging should be
sorted, taken to a recycle centre and
disposed of in a manner which is
compatible with the environment.
When the product is no longer required, it
must be disposed of in an environmentally
protective way.
Battery Removal.
Refer to section 3.1 for battery removal.
Dispose of batteries according to local
authority guidelines.
under the Waste Batteries and
Accumulators Regulations 2009, Jack
Sealey Ltd are required to inform potential
purchasers of products containing batteries
(as defined within these regulations), that
they are registered with Valpak's registered
compliance scheme.
Jack Sealey Ltd's Batteries Producer
Registration Number (BPRN) is BPRN00705
01284 757500
01284 703534
button. A minus
www.sealey.co.uk
Web
sales@sealey.co.uk
email
STW306
Issue: 1 - 04/10/11
Advertisement
