Sealey YK30F.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY
 Familiarise yourself with this products application and limitations,
as well as the specific potential hazards peculiar to the press.
 Maintain the press in good condition (use an authorised service
agent).
 Replace or repair damaged parts. Use recommended parts only.
Non authorised parts may be dangerous and will invalidate the
warranty.
 Keep the press clean for best and safest performance.
 Locate the press in a suitable working area for its function, keep
area clean, tidy, free from unrelated materials and ensure there
is adequate lighting.
 Ensure the workpiece is correctly secured before operating the
press.
 WARNING! Always wear approved eye or face protection when
operating the press.
 Remove ill fitting clothing. Remove ties, watches, rings, loose
jewellery and contain long hair.
 Keep hands and body clear of the work table when operating the
press.
 Maintain correct balance and footing. Ensure the floor is not
slippery and wear non slip steel toe-capped shoes/boots.
 Keep children and unauthorised persons away from the working
area.
 DO NOT operate the press if any parts are missing as this may
cause failure or possible personal injury.
 DO NOT use to compress springs or any other item that could
disengage and cause a potential hazard.
 DO NOT stand directly in front of the loaded press and never
leave a loaded press unattended.
 DO NOT force the press to achieve a task it was not designed
to perform.
 DO NOT make any modifications to the press.
 DO NOT adjust or tamper with the safety valve.
 DO NOT exceed the rated capacity of the press.
 DO NOT apply off centre loads.
 DO NOT allow the workpiece or the arbor plates to fall from the
press working bench.
 DO NOT get the press wet or use in damp or wet locations or
areas where there is condensation.
 DO NOT operate the press when you are tired, under the
influence of alcohol, drugs or intoxicating medication.
 When not in use release pressure from the pump and clean the
press. Stand or store the arbors in a safe location.
 WARNING! Always position the press against a wall. If the
press is situated in the open workshop, it is essential that
a guard be placed at the rear of the unit. This will prevent
injury to bystanders in the event of the work piece ejecting
suddenly.
 WARNING! The warnings, cautions and instructions in this
manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be
built into this product, but must be applied by the operator.
DANGER! The press is top heavy. If it requires moving after

assembly or for relocation, use suitable slings around the top
crossbeam, or lift direct with a forklift with the forks located under
the top crossbeam. DO NOT use a pallet truck.
2. INTRODUCTION & SPECIFICATIONS
Steel frame construction with hydraulic pump unit. Sliding hydraulic
ram assembly gives 260mm of lateral travel for off-centre pressing
applications. Frame head fitted with ram pressure gauge. Supplied
with flat pressing plate/V-blocks.
INSTRUCTIONS FOR:
HYDRAULIC PRESS 30tonne FLOOR TYPE
MODEL No:
Model:
Type:
Capacity:
Ram Stroke:
Lateral Ram Travel:
Maximum Height - Ram to Table:
Minimum Height - Ram to Table:
Table Aperture:
Working Table Depth:
Working Table Width:
Overall Height:
Gauge Included:
Weight:
Original Language Version
YK30F.V2
YK30F.V 2
YK30F.V2
Floor
30tonne
150mm
260mm
1131mm
52mm
164mm
188mm
550mm
1975mm
Yes
177kg
Issue: 2 - 21/11/11