Advertisement
Quick Links
Mounts by
A division of David Engineering & Mfg. Inc.
Model
AWM125-120 ARTICULATING WALL MOUNT INSTRUCTIONS
Thank you for purchasing the PDR mount.
To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship. We are not liable
for improper installation that results in damage to mounts, adapters or presentation equipment.
To register visit our web site @ www.pdrmounts.com
Special techniques are necessary for installation of the panel display mount.
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for t
mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat a
airflow.
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight
display and the wall mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Features
Simple to adjust
Adapter plate included
125 lb rated
AWM 125-120 FITS 22" TO 36" DISPLAYS
Rugged heavy gauge metal construction
Tough powder-coated finish
Extends 20.7" from the wall and closes to under 4.6"
Pivots left or right, tilts up 5 deg. and down 15 deg.
3 adjustable height positions
Includes cable management system
Tension bolts to adjust smooth action and eliminate creep
Fig 1
1
for future reference.
he
nd
of both the panel
Advertisement
Summary of Contents for PDR AWM125-120
- Page 1 To ensure the correct usage, please read and follow the instructions manual thoroughly. Please store the instructions in a safe place for future reference. All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship. We are not liable for improper installation that results in damage to mounts, adapters or presentation equipment.
-
Page 2: Installation Location
INSTALLATION LOCATION WARNING The wall where the wall mount is to be installed must be capable of long-term support of the total load of the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to withstand the force of earthquakes, vibration and other external forces. -
Page 3: Supplied Hardware
SUPPLIED HARDWARE SP-E-32-10-01 PH-M-08-16-00 PH-M-08-40-00 M8 X 40 PAN HEAD PHILLIPS MACHINE SCREW M8 X 16 PAN HEAD .32 ID X .75 OD X 1.00 LONG 4 REQUIRED PHILLIPS MACHINE SCREW PLASTIC SPACER 4 REQUIRED 4 REQUIRED PH-M-06-16-00 PH-M-04-16-00 PH-M-06-40-00 M6 X 40 PAN HEAD M4 X 16 PAN HEAD PHILLIPS MACHINE SCREW... - Page 4 DRAWING SPECIFICATIONS Model AWM125-120 Single stud articulating wall mount 15 DEG 20.7 5 DEG 24.00 8.05 3.07 4.67 14.00 5.39 4.00 4°...
- Page 5 The height of the AWM125-120 should be mounted at the same horizontal center line as the desired display center line (viewing center line). 1:Position the AWM125-120 mount to the desired position. Mark and Pre drill the top and bottom holes with a 3/16” (5mm) hole . SEE FIG 2 2: Insert the lag bolt and washer (item 11 and 12) into the top hole and secure to the AWM125-120 mount.
- Page 6 3: Two other tension bolts can be tightened or loosened to suit. SEE FIG 6 2: Adjust the tilt by loosening the Tri knob on the side of the AWM125-120 and adjust back or forward for best viewing angle. See fig 6 3: Place the plastic tie holders (16) in the desired holes, and using zip ties (14) attach the cables.