Page 5
一般故障排除指南 问题描述 潜在原因 解决办法 1. 冲水不良 a. 水位线比要求的低 a. 重新调整水位至正确水位线 b. 冲水阀拍盖关闭过快或没打开 b. 检查有无脏物附着在出水阀拍盖 c. 冲水按钮或手柄损坏需更换 c. 更换 d. 水压过低 d. 正常水压必须高于20psi e. 座厕排污水道或排污管堵塞 e. 清理堵塞 f. 使用水箱清洁剂有沉淀物 f. 清理水箱,停止使用水箱清洁剂 g. 楼房无管道排气孔 g. 安装管道排气孔 a. 水位过高,高于水件溢水口 a. 重新调整水位至正确水位线 2. 漏水 b.
Toilet Installation manual 39320000 99.0575.031/ECN 235920/11.15 Remark: This installation manual is only for installing the ceramic parts. For the tank trim or seat & cover installing, please refer to relative manual. Unit: mm ROUGH-IN DIMENSIONS Finished floor Finished floor Dimensioning diagrams are provided for each model.
Page 8
Installation of concealed tank INSTALL CONCEALED TANK INSTALL BOLTS Finished wall Finished wall Cover for water inlet Fixing bolts Cover for water outlet Install concealed tank and tank fittings according to According to the picture shown, finish the wall and install concealed tank installing instructions, and pre-install the bolts, then pull out the cover of water inlet and water the expansion bolts.
INSTALL SEAT&COVER Install the seat & cover according to seat & cover installation manual. Apply a silicone putty(not supplied) along the intersecting edge of the toilet base, ensuring a complete seal. Remove excess sealant. Note: Using cement to fix the toilet is prohibited. Install the sensor INSTALL PREPARATION Suggested dimension...
Page 10
INSTALL THE CONNECTOR 2.1 Cutting 2.2 Nibbing 3170000179 2.3 Applying PVC cement 2.4 Installing Water supply 355mm 50-55mm 220mm Finished floor 50-55mm POSITION THE TOILET FINISH THE TOILET Rubber washer Bolts cap Tighten the bolts to fix the toilet as picture shown, Install the sensor and seat &...
Using this guide and referring to the accompanying instructions should help you solve most TROUBLE SHOOTING GUIDE common problems encountered. Problem Possible Cause To Correct a. Water level in tank is below prescribelevel. a. Set to prescribed level. 1. Poor flushing action b.
WALL HUNG TOILET 挂墙式座厕安装说明书 39321000 99.0575.031/ECN 235920/11.15 39321000 Installation Manual Thank you for selecting our products which have been the benchmarks of fine quality for years.To help ensure that the installation process will proceed smoothly, please read these instructions carefully before you begin.
Page 14
CONCEALED TANK INSTALLATION Tank Installation Wall Finishing Preparation Finished wall Cover for water inlet Fixing bolts Cover for water outlet Install the concealed tank and tank fitting Before finishing the wall, install the fixing bolts first. according to it’s installation manual. Cover the water inlet &...
Page 15
Connectors Installation Apply PVC solvent cement (not supplied) evenly inside the outlet hole, then insert the plastic outlet connector. Insert the water supply pipe into the water supply line from the tank. Push Button Installation Fixing the Toilet Push button Install the toilet and check the levelness side to side, tighten the bolts to fix the toilet as shown, then cover Install the push button according to installation...
INSTALLATION WITH FLUSH VALVE SENSOR Installation of the “ L ” Bracket Suggested Dimension Finished floor Finished floor BACK VIEW Unit : mm. Installation of the Sensor 20 mm. 355 mm. 220 mm. 50-55 mm. Finished floor 70-75 mm. 3.1 Cutting and chamfer 3.2 Applying PVC cement solvent 3.3 Install the connector as shown.
Do not use cleansers in tank. Products containing chlorine(calcium hydrochlorite) can seriously damage fitings in the tank. This damage can cause leakage and property damage. GROHE shall not be responsible or liable for any tank fitting damage caused by the use of cleansers containing chlorine (calcium hydrochlorite) Nov.15...
Need help?
Do you have a question about the 39320000 and is the answer not in the manual?
Questions and answers