Download
 Share
 Print this page
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Enclosure
  5. CAB1-X
  6. Installation instructions manual

Siemens CAB1-X Installation Instructions Manual

System enclosure for nccnt wan.
Hide thumbs
   
1
2
3
4
5
6
7
8

Advertisement

Model CAB1-X
System Enclosure for NCCNT WAN
INTRODUCTION
PRE-INSTALLATION (Optional)
P/N 315-034369-4
The Model CAB1-X enclosure from Siemens Industry, Inc., is used to house system
modules. The CAB1-X backbox and doors are black. The CAB1-X consists of an outer
door, an OD-GP vented grill plate, a mounting plate (CAB-MP), and a backbox as
shown in Figure 1.
OD-GP GRILL PLATE
OUTER DOOR
Figure 1
CAB1-X Enclosure
The backbox is mounted on a flat surface with four user-supplied bolts that are a
maximum of
3
/
inch in diameter.
8
The backbox contains enough space to mount a set of BTX-1 (31 AH) batteries in the
bottom.
Remove the CAB-MP mounting plate from the backbox.
BACKBOX
MOUNTING PLATE
Siemens Industry, Inc.
Building Technologies Division
Previous page
Next page

Advertisement

Table of Contents

   Related Manuals for Siemens CAB1-X

   Summary of Contents for Siemens CAB1-X

  • Page 1: Installation Instructions

    The Model CAB1-X enclosure from Siemens Industry, Inc., is used to house system modules. The CAB1-X backbox and doors are black. The CAB1-X consists of an outer door, an OD-GP vented grill plate, a mounting plate (CAB-MP), and a backbox as shown in Figure 1.
  • Page 2 Mark, drill, and install the two bottom bolts in the backbox. Tighten all four bolts securely against the back wall of the backbox. 26.12 21.25 MOUNTING HOLES FOR 18.00 CAB1-X 27.00 Figure 2 CAB1-X Mounting Holes Siemens Industry, Inc. P/N 315-034369-4 Building Technologies Division...
  • Page 3 0.25 in. (6.35 mm) or by a noncon- ductive sleeve or nonconductive barrier from all other conductors. If energy limited cable or equivalent is not used within the CAB1-X enclosure, then the following guidelines do not apply. In that case, be sure to follow standard wiring practices.
  • Page 4 KNOCKOUTS (16 PLACES) Figure 4 CAB1-X Knockouts POST-INSTALLATION After the backbox is installed and the wiring completed, finish the installation by installing the mounting plate, the outer door, the OD-GP grill plate, and the ground straps.
  • Page 5 DOOR HINGE Figure 5 Installing The Door On The CAB1-X OD-GP GRILL PLATE CAB1-X DOOR Figure 6 Installing The OD-GP Grill Plate On The CAB1-X Door Siemens Industry, Inc. P/N 315-034369-4 Building Technologies Division...
  • Page 6 GROUND STRAP ON DOOR Figure 7 Ground Strap Installation Siemens Industry, Inc. P/N 315-034369-4 Building Technologies Division...
  • Page 7 This page has been left intentionally blank. Siemens Industry, Inc. P/N 315-034369-4 Building Technologies Division...
  • Page 8 This page has been left intentionally blank. Siemens Industry, Inc. Siemens Building Technologies, Ltd. Building Technologies Division Fire Safety & Security Products Florham Park, NJ 2 Kenview Boulevard Brampton, Ontario L6T 5E4 Canada P/N 315-034369-4...

Comments to this Manuals

Symbols: 0
Latest comments: