Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Addonics Technologies AEMEDUSIB25F
Summary of Contents for Addonics Technologies AEMEDUSIB25F
- Page 1 Addonics T E C H N O L O G I E S Combo Hard Drive USIB25 Mobile Rack USIB25 For following models: AEMEDUSIB25U, AEMEDUSIB25F, AEMEDUSIB25C, AEMEDUSIB25S, AEMEDUSIB25UW, AEMEDUSIB25FW, AEMEDUSIB25CW, AEMEDUSIB25SW, AERHDUS25I, AERHDUS25WI Users Guide Revision 1.0...
-
Page 2: Fcc Warning Statement
Increase the distance between the equipment and the receiver • Connect the equipment to a different power outlet other than the one where receiver is connected • Consult a certified television or radio technician Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0... - Page 3 Chapter 3 USB Interface Cable Installation ........10 Serial ATA Interface Cable Installation ......11 Firewire Interface Cable Installation ........ 12 CardBus/PCMCIA Interface Cable Installation ..13-16 Technical Support & Contact Information ........…17 Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 4 Preface This is a Preliminary version of the manual intended to provide advance information on the Addonics Technologies’ Combo Hard Drive USIB25. The information is as complete and as accurate as possible as of the publication date, but will be superseded and updated periodically by revised manuals. The contents are subject to change without notice.
-
Page 5: Chapter 2 Hardware Installation Guide
Chapter 2 Hardware Installation Guide Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0... - Page 6 ! Only one data cable connection at anytime. Cannot have IDE cable connected or any USIB cable connected at the same time. ! DO NOT REMOVE The jumper block on the USIB board It is for the activity light. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 7 ! To get power from the Interface cable (Bus Power) the power switch must be set closer to the IDE connector. ! When the drive cradle is powered from the interface cable no PC power supply is needed. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 8 JP2 and JP3. jumpers in JP2 and JP3. These spare jumpers These spare jumpers should be sitting on the should be sitting on the outer pin only outer pin only Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 9 Interface Cable such as USB, Firewire etc. Note: ! We recommend setting the hard drive to MASTER mode/setting at all times. (Default setting) ! We recommend using AC/DC power adapter to power the hard drives. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
-
Page 10: Cable Installation
Please check the motherboard documentation for the correct header pin out of your USB port. To the Motherboard header. To the USB Interface Cable Connector Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0... - Page 11 Note: USB Combo Hard Drive25 is Plug and Play under Windows XP, And Me, 2000. There is no third party driver needed. Brand New Hard drive must be Partitioned and Formatted first. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 12 Double Click on the “My Computer” icon if not open yet. You are now ready to use the Combo hard drive kit. Note: Brand New Hard drive must be Partitioned and Formatted first. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 13 Double Click on the “My Computer” icon if not open yet. You are now ready to use the Combo Hard Drive25 kit. Note: Brand New Hard drive must be Partitioned and Formatted first. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 14 CardBus/PCMCIA USIB Driver Installation For Windows 95, 98, 98SE and Me (Do not run the SETUP program from the driver disk, SETUP Is for DOS or WIN 3.1 using PCMCIA mode only) Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 15 2. Double Click SCSI adapter icon 3. Click on the Driver Tab 4. Click Add to add new driver 5. Follow wizard and browse to A:\NT folder for the Driver. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 16 8. Double Click on the “My Computer” icon. You are now ready to use The Combo Hard Drive25 kit. Note: Brand New Hard drive must be Partitioned and Formatted first. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
- Page 17 12. Let the OS install the Driver and that's it. Click Finish. Click YES to restart the Computer if prompted and that's it. Note: Brand New Hard drive must be Partitioned and Formatted first. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
-
Page 18: Contact Information
San Jose CA, 95131 Phone: 408-433-3899 Fax: 408-433-3898 Email: ATC@Addonics.com Internet: http://www.addonics.com TECHNICAL SUPPORT Phone: 408-433-3855 Hours: 8-5 PST Email: Techinfo@addonics.com Please visit our web site www.addonics.com to register your warranty online. Addonics Technologies – Combo Hard Drive USIB25 Users Guide v1.0...
Need help?
Do you have a question about the AEMEDUSIB25F and is the answer not in the manual?
Questions and answers