Advertisement
6.1.6. Squeeze the trigger for no more than half a second, so as not to overheat the fitting to be welded. This could 'cook' it and make it less
resistant against being ripped out.
DO NOT keep the gun in place for too long as it may overheat or burn a hole in the panel.
6.1.7
DO NOT release the pressure on the welding surface until you have released the trigger or the circuit may be prematurely broken.
6.1.8. Allow 1 minute between applications to allow the welder to cool down.
6.1.9. When the task is complete, disconnect the tool from the power supply and store in a safe area.
Note: DO NOT use the welding gun continuously for long periods, as the gun may overheat.
6.2.
Slide Hammer
6.2.1. Grip the nail in the slide hammer spindle and then operate the striking hammer until the dent is pulled out. To pull a washer, grip the
washer hook (fig.1.7) in the spindle and hook the washer. See fig.4.
6.3.
Sheet Heating
Use the heating electrode (fig.1.8) and extension (fig.1.9), for localised sheet heating in order to shrink and remove small dents
and pimples. Proceed as 6.1. above, omitting 6.1.5. Carefully heat the localised area accordingly.
IMPORTANT; If the electrode, electrode holder, carrier contact face (fig. 4.A) and panel are not clean, dry and free from paint,
grease, rust etc. the weld will be poor and the welder may overheat, causing irreparable damage to the casings.
fig.3
7. MAINTENANCE
WARNING: Unplug from the mains power supply before performing maintenance or service.
7.1.
Check all electrical components as stated in Section 1.
7.2.
Using a cloth or a brush, regularly clean the transformer cooling slots.
7.3.
Replace or repair damaged parts. Use recommended parts only, unauthorised parts may be dangerous and will invalidate the warranty.
7.4.
Keep the handgrips of the welder dry, clean and grease free.
7.5.
Always keep the surfaces of the electrodes and of the electrode holding barrels free from any oil, grease, dust, paint, etc., in order to
allow proper flow of current.
7.6.
After you have finished using the gun, allow it to cool and then return it, and the accessories, to the case for safe storage.
8.
CONSUMABLES
The following items are available through your local Sealey dealer. All are supplied in packs of 100.
Part No.
Description
PS/0002
Nails, 2.5 x 50mm
PS/0003
Nails, 2.0 x 50mm
PS/0004
Washer, 8 x 16 x 1.5mm
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
Part No.
Description
PS/0006
Rivet, 3 x 3.2mm
PS/0007
Rivet, 3 x 4.5mm
PS/0009
Threaded Rivet, 4 x 15mm
01284 703534
sales@sealey.co.uk
Original Language Version
fig.4
www.sealey.co.uk
SR20.V3 Issue: 2(L) - 19/07/17
Advertisement
