Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Motorline MC11
Summary of Contents for Motorline MC11
- Page 1 MC11 MC11 USER’S AND INSTALLER’S MANUAL V2.0 REV. 05/2019...
- Page 2 00. CONTENT 01. SAFETY INSTRUCTIONS INDEX ATTENTION: 01. SAFETY INSTRUCTIONS This product is certified in accordance with European 02. THE CONTROL BOARD Community (EC) safety standards. TECHNICAL SPECIFICATIONS CONNECTOR’S DESCRIPTION This product complies with Directive 2011/65/EU of the PROGRAMMING PRE-RECOMENDATIONS European Parliament and of the Council, of 8 June 2011, on 03.
- Page 3 01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. very important. Read all instructions carefully before beginning the WARNINGS FOR TECHNICIANS installation/usage procedures and keep this manual in a safe place that it can be consulted whenever necessary.
- Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY September 2009. • Attach the permanent label for the manual release as close as possible • Supplier disclaims any liability if: to the release mechanism. • Product failure or deformation result from improper installation • Disconnect means, such as a switch or circuit breaker on the electrical use or maintenance! panel, must be provided on the product’s fixed power supply leads in •...
- Page 5 02. THE CONTROL BOARD TECHNICAL CHARACTERISTICS CONNECTOR’S DESCRIPTION The MC11 is a 24Vdc or 12Vdc electronic central unit for the automation of swing gates, sliding gates and bollards with radio receiver and built-in battery charger. • Transformer supply 110V/230Vac 50/60Hz 120W máx.
- Page 6 02. THE CONTROL BOARD 03. PROGRAMMING PROGRAMMING PRE-RECOMENDATIONS MAIN MENU •PROGRAMMING THE CONTROL BOARD - BUTTONS SEL/SET The MAIN MENU contains the main functions for automation programming, with direct access via the SEL key. MAIN MENU SEL button: It makes the selection of the function to change. The selection is identified by the flashing of the LED corresponding to the selected function at that time.
- Page 7 • CODE | PROGRAMMING OF COMMANDS FOR TOTAL OPENING programming and take the programmed course manually. With working The control board accepts only Dip-Switch or Rolling Code MOTORLINE transmitters, and No working time Factory setting: Working Time = 30sec time has a maximum capacity of 120.
- Page 8 03. PROGRAMMING 03. PROGRAMMING MAIN MENU MAIN MENU • T. MOT. PED | PROGRAMMING PEDESTRIAN WORKING TIME Program time: 01 •Press SEL button the times necessary until the T. PAUSA LED starts to flash. 02 • Press the SET button for 1 second. To activate the pedestrian function, the control board allows to be just activated the operation of motor 1.
- Page 9 03. PROGRAMMING 03. PROGRAMMING EXTENDED MENU 1 EXTENDED MENU 1 The control panel has an EXTENSIVE MENU 1, with more functions for programming. 01 • Enter the Extended Menu 1. To access the options of extended menu 1 follow these instructions: 02 •...
- Page 10 03. PROGRAMMING 03. PROGRAMMING EXTENDED MENU 1 EXTENDED MENU 2 The control panel has an EXTENSIVE MENU 2, with more functions for programming. Activate Opening Push with the force set on the potentiometer: To access the extended menu 2 options proceed as follows: 01 •...
- Page 11 03. PROGRAMMING 03. PROGRAMMING EXTENDED MENU 2 EXTENDED MENU 2 • AUTO PGM | • CODE PED | PHOTOCELL TEST (DS CONNECTION) FLASHLIGHT PAUSED With this function, you can test the connection of photocells. With the function on, whene- With this option enabled, whenever the engine is in standby time the 24V output for firefly ver you receive an opening order, there is a momentary interruption in powering the photo- will remain on.
- Page 12 03. PROGRAMMING EXTENDED MENU 3 Extensive menu 3 allows you to set the speed of the motor slowdown. Factory setting: Level 3 Access Extension Menu 3: 01 • Access the extended menu 1 (page 8A). 02 • Access the extended menu 2 (page 9B). 03 •...
- Page 13 04. CONNECTION SCHEME COMPONENT'S CONNECTION TO THE CONTROL BOARD...
- Page 14 3 • Disconnect the motors from the control board and test them connected directly to a 12 / 24V battery to find out if it is malfunctioning. 4 • If the motor works, the problem is on the control board. Pull it out and send it to the MOTORLINE technical services for diagnosis;...
Need help?
Do you have a question about the MC11 and is the answer not in the manual?
Questions and answers