IKA A10 basic Operating Instructions Manual
  1. Manuals
  2. Brands
  3. IKA Manuals
  4. Laboratory Equipment
  5. A10 basic
  6. Operating instructions manual

IKA A10 basic Operating Instructions Manual

Hide thumbs Also See for A10 basic:
Table of Contents

Advertisement

Quick Links

20000003970
A10 basic_062016
A10 basic
®
IKA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A10 basic and is the answer not in the manual?

Questions and answers

Related Manuals for IKA A10 basic

Summary of Contents for IKA A10 basic

  • Page 1 20000003970 A10 basic_062016 A10 basic ®...

  • Page 2: Table Of Contents

    Source language: German Contents Page Declaration of Conformity Explication of warning symbols Safety instructions Correct use Unpacking Useful information Commissioning Timer function Interval function Exchanging and replacing the grinding tools Maintenance and cleaning Error codes Accessories Warranty Technical data Declaration of Conformity We declare under our sole responsibility that this product corresponds to the regulations 2014/35/EU, 2006/42/EC, 2014/30/EU and 2011/65/EU and conforms with the standards or normative: EN 61010-1, EN 6010-2-051, EN 61326-1, EN 60529 and EN ISO 12100.

  • Page 3: Safety Instructions

    • The feet of the instrument must be clean and undam- cooled with liquid nitrogen, please cool them first be- aged. fore filling into A10 basic grinding chamber. • The instrument is not suitable for hand held operation. • The instrument may heat up when in use.

  • Page 4: Correct Use

    Correct use • Use The mill is not suitable for grinding WARNING The A10 basic is a batch mill that allows for both im- wet material with too much water. pact milling and cutting milling. Otherwise, the water may leak from the chamber and damage the device.

  • Page 5: Useful Information

    Impact milling: especially if there is uncertainty about the danger of ex- The A10 basic with a beater reduces soft, medium hard plosion (dust explosion as a result of electrostatic charge). and brittle materials with a Mohs’ scale of hardness of up to 5.
  • Page 6 The grinding chamber may only be filled halfway espe- cially when samples containing oils and similar materials The A10 basic offers following cooling processes: are ground. First put the feed product into the grinding pot and then Note: Moisture in material that is ground may evaporate add crushed dry ice.

  • Page 7: Commissioning

    Commissioning Pay attention to the ambient conditions listed in the When the mains plug is plugged in, all of the LEDs light up “Technical data“. briefly during the self check. Check whether the voltage specified on the type plate matches the mains voltage available. The power socket used must be Then, the software version is displayed.

  • Page 8: Exchanging And Replacing The Grinding Tools

    Exchanging and replacing the grinding tools Disconnect the mains plug prior to Note: When removing the A10.2 Star-shaped beater, use exchanging or replacing the grinding the hooks on the bracket to hold the cutter. Then, the cut- tools! ter can be taken out of the chamber (see Fig. 9, Fig. 10). Exchanging and replacing the grinding tools as following: Fig.

  • Page 9: Maintenance And Cleaning

    Maintenance and cleaning Maintenance If grinding tools wear out over the course of time, espe- cially as a result of constant grinding of very hard materi- Hex. nut als, so that rapid grinding with the appropriate quality is Grinding tool no longer possible.
  • Page 10 When ordering spare parts, please give: - machine type - serial number, see type plate - item number and designation of the spare part, see www.ika.com, spare parts diagram and spare parts list, - Software version. Repair Please send equipment for repair only after it has been cleaned and is free from any materials which may constitute a health hazard.

  • Page 11: Error Codes

    A10.2 Star-shaped knife A10.3 Hard metal cutter A10.4 Grinding chamber reduction Warranty In accordance with IKA ® warranty conditions, the war- The warranty does not cover worn out parts, nor does ranty period is 24 months. For claims under the warranty it apply to faults resulting from improper use, insufficient please contact your local dealer.

  • Page 12: Technical Data

    Technical data Operating voltage 220–240 ± 10 % 100–120 ± 10 % Frequency 50 / 60 Motor rating input Motor rating output Rated speed 25000 ± 2 % Maximum circumferential speed Motor brushless motor Maximum useful volume Maximum feed hardness Mohs Maximum feed grain size 6 –...

Table of Contents

Save PDF