Related Manuals for Hengx HAIC-N Series
Summary of Contents for Hengx HAIC-N Series
- Page 1 Digital Counting Scale HAIC-N Series _________________________________________ User’s Manual...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Before Using the Scale ....................1 Instruction for Use ......................1 Preparing to Use the Scale.................... 1 CHAPTER I INTRODUCTION ................. 2 Features and Specification ................ 2 Display ...................... 3 Keyboard Function ..................4 Operating the Scale ................... 5 1.4.1 Power On.................. -
Page 3: Before Using The Scale
HAIC-N Series BEFORE USING THE SCALE Thank you for purchasing High Precision Electronic Counting Scale. In order to use the scale properly, please read this User Manual carefully before use. If you have any problem with scale, please contact your supplier. -
Page 4: Chapter I Introduction
HAIC-N Series 9. Please note when the display shows ------ BAT LO , it’s means the battery need to be charged. CHAPTER INTRODUCTION 1.1 FEATURES AND SPECIFICATION Features: Internal resolution: 1/1,000,000 LCD display (digit height 7mm x 16mm) with LED backlight ... -
Page 5: Display
HAIC-N Series Power supply Rechargeable battery or AC adaptor DC 9V Connector 5 pin d socket Loadcell connection: Pin 1: +E Load cell excitation positive Pin 2: -E Load cell excitation positive Pin 3: +S Load cell excitation positive Pin 4: -S Load cell excitation positive Pin 5: GND Load cell cable shield 1.2 DISPLAY... -
Page 6: Keyboard Function
HAIC-N Series [APW MODE] : When the scale is in APW mode, this arrow will on [SMPL MODE] : When the scale is in SMPL mode, this arrow will on [ACCUMULATION MODE] : When the scale is in accumulation mode, this arrow will on... -
Page 7: Operating The Scale
HAIC-N Series M+/MR : Adds the indicated weight or piece count value into accumulation memory MC : Clears the memories of the accumulation PRESET CHECK: To setup the Count Pre-set (Check-weighing) function PRESET APW : Inputs the indicated value entered via the numeric keypad as a Pre-set value 1.4 OPERATING THE SCALE... -
Page 8: Zeroing The Display
HAIC-N Series 2.3) The max. weighing range of the scale is - The max. weighing range of the scale plus 9d, if the object on the pan is over then the max. weighing range, the display shows as ff. then the beeper sounds, please remove the object to be able to continue operate the scale 1.4.2 Zeroing the Display... -
Page 9: Entering A Know Piece Weight
HAIC-N Series To clear the tare value, press TARE key with the pan empty. The weight window will back to zero and the tare indicator is off 1.4.4.2 With an existing weight on the pan (ex. 5305g): Enter a numeric value (ex. 305g), then press TARE key. The net weight will be displayed. -
Page 10: Sampling, Calculation Average Piece Weight(Apw)
HAIC-N Series 1.4.5.2 Place the sampling object to count the quantity To exit APW mode, press Clear key. The piece weight window will back to zero and the APW indicator is off 1.4.6 Sampling, Calculating Average Piece Weight (APW) 1.4.6.1 Place the desired sample onto the weighing pan. -
Page 11: Accumulation: Weight
HAIC-N Series To exit SMPL mode, press Clear key. The piece weight window will back to zero and the SMPL indicator is off 1.4.7 Accumulation: Weight 1.4.7.1 Place object on the weighing pan (ex. 885g) 1.4.7.2 Wait until scale becomes stable, and then press M+/MR key, (Accumulation indicator is on) -
Page 12: Recalling Accumulated Memory: Weight
HAIC-N Series 1.4.7.6 Please repeat [1.4.7.4~1.4.7.5] if there are various objects to be accumulate 1.4.7.7 If the total accumulated weight is over the max. display weight (99999.9), the display will show as ff. Press MC key to clear the accumulated memories and the ACCUMULATION indicator is off 1.4.8... -
Page 13: Accumulation: Quantity
HAIC-N Series 1.4.9 Accumulation: Quantity The scale should be in the APW or SMPL mode before the user can accumulate the quantity, please refer sec. 1.4.5 and 1.4.6 1.4.9.1 Place objects on the weighing pan [ex. 885g;15pcs], and wait the scale becomes stable, then press M+/MR key, display shows as ff. -
Page 14: Recalling Accumulated Memory: Quantity
HAIC-N Series 1.4.9.5 Please repeat [1.4.7.4~1.4.7.5] if there are various objects to be accumulate 1.4.9.6 If the total accumulated weight or quantity is over the max. display weight (99999.9) or the max. display quantity (999999), the display will show as ff. -
Page 15: Storing Piece Weight Into Memory
HAIC-N Series Press MC key to clear the accumulated memories and the accumulation indicator is off 1.4.11 Storing Piece Weight into Memory 1.4.11.1 The scale should be in the APW or SMPL mode before the user can storing the piece weight into memory, please refer sec. -
Page 16: Recalling The Preset Piece Weight
HAIC-N Series 1.4.12 Recalling the Preset Piece Weight 1.4.12.1 The scale should be in the normal weighing mode before the user can recall the piece weight from memory, enter the location via numeric key which will be recalled (ex. 19) 1.4.12.2 Then press PRESET APW key to recall the piece weight, display will shows as ff. -
Page 17: Preset Check : Quantity
HAIC-N Series 1.4.13 Preset Check : Quantity It’s available to pre-set the upper limit of quantity under APW or SMPL mode. If the counts are over the limit, the beeper makes warning sounds, and the weight window displays -0.qty- flashing 1.4.13.1 Upper limit of pre-setting quantity, in the APW or SMPL mode whether there is object on... -
Page 18: Preset Check : Weight
HAIC-N Series 1.4.13.3 Press PRESET CHECK key to confirm, then the scale back to APW or SMPL mode 1.4.14 Preset Check : Weight It’s available to pre-set the upper limit of weight under normal weighing mode. If the weight is over the limit, the beeper makes warning sounds, and the quantity window displays -o.wt- flashing 1.4.14.1 Upper limit of pre-setting weight, in normal weighing mode whether there is object on... -
Page 19: Power Supply
HAIC-N Series 1.5 POWER SUPPLY POWER SELECTION 1. 6V4Ah rechargeable battery 2. 110V/220V AC adaptor DC 9V POWER CONSUMPTION 1. Approximately DC 43mA (Scale) Usage time approximately 100 hours 2. Approximately DC 80mA (Scale + Display backlight) Usage time approximately 80 hours... -
Page 20: Chapter Ii Advanced Functions
HAIC-N Series 2.1 C101_Calibration A. Setting up division, decimal point, max. capacity and calibration Press and hold “M+/MR” key，then turn on the scale，to enter division setting: In kg for the calibration unit, do not accept other units) 1. Division Setting： (unit is in kg) -
Page 21: Appendix : Lcd Word Table
HAIC-N Series “M+/MR” key to confirm, scale will move into the weighing mode automatically after calibration. Ex. LCD shows [01.0000] [ FULL] [ SEt] ，Press “M+/MR” key，the weight value is set to 1 kg，End of the calibration, 1 kg weight bar display. - Page 22 HAIC-N Series ?/Others...
Need help?
Do you have a question about the HAIC-N Series and is the answer not in the manual?
Questions and answers