Summary of Contents for Black & Decker ProFinish X700 Series
CONSERVER CE GUIDE D’ENTRETIEN ET D’UTILISATION ProFinish Premium Irons Planchas de primera Fers de qualité Household Products Limited de México S. de R.L. de C.V. 1200W 120V~ ™ U.S.A./CANADA 1-800-231-9786 MEXICO 60Hz http://www.householdproductsinc.com Séries X700 - X800 Series ® 01-800-714-2503...
READ ALL INSTRUCTIONS BEFORE USING. s Use iron only for its intended use. s To protect against a risk of electric shock, do not immerse the iron in water or other liquid. s The iron should always be turned Off before unplugging from an outlet.
Be careful to avoid spilling water over iron when filling. s Do not operate iron with a damaged cord or plug or if the iron has been dropped or damaged. s To avoid the risk of electric shock, do not disassemble the iron;...
When using surge of steam, always direct the steam vents away from your body. s Do not operate in the presence of explosive and/or flammable fumes. s Do not use iron outdoors. s This product is for household use only not for commercial or indus- trial use. SPECIAL INSTRUCTIONS s To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.
SAVE THESE INSTRUCTIONS POLARIZED PLUG This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug.
Before shipping or mailing your iron, empty all water from the iron. Plug in the cord and heat the iron at setting 7 for a few minutes. Iron continu- ously over an all cotton cloth for about 2-3 minutes. Place the iron on its heel rest and leave it operating for 7 to 8 minutes.
FULL ONE-YEAR WARRANTY Household Products warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the origi- nal date of consumer purchase or receipt as a gift. This warranty does not include damage to the product resulting from accident or misuse.
ENGLISH 1. Water Fill Hole Cover 2. Spray Nozzle 3. Temperature Selector/Smart Steam™ Dial 4. Magnifying Lens 5. Spray Button 6. Surge of Steam Button ® 7. Comfort-Grip handle 8. Pivoting Cord ESPAÑOL 1. Tapa del orificio de llenado 2. Rociador de agua 3.
NOTE: Be sure to aim the spout of the cup into the slot of the Water Fill Hole and fully close the Cover. If water spills over the Fill Hole, set the iron on its Heel Rest, plug in, and heat for 1-2 minutes to dry. Refill as needed.
5. Allow to preheat for approximately 2-3 minutes. 6. If leaking/spotting occurs from the soleplate or Fill Hole while ironing, set the iron on its Heel Rest and heat for 1-2 minutes to dry before resuming ironing. 4. Enchufe la plancha. Oprima el botón ON/OFF (apagado/encendido), y se encenderá...
Lorsque la pulvérisation n’est pas suffisante, pomper le bouton de pulvérisa- 7. Push the ON/OFF button to manual- ly turn off the iron and the light will go out. If unattended, the iron will automatically shut off in 10 min- utes.
Push the SPRAY button for a fine mist of water. If spray is light, pump the SPRAY button several times. Check to be sure the iron is filled with water. Move the Lever to the DRY position to iron without steam. It is not neces- CONSEJOS PARA PLANCHAR •...
• Use SPRAY to dampen tough wrinkles at any temperature setting. CARE OF THE IRON 1. It is not necessary to empty the water after each use if the iron is used frequently. However, when you want to empty the water, move the lever to STEAM CLEAN, press the ON/OFF button so the light goes out.
Never use abrasives, heavy-duty cleansers, vinegar, or scouring pads. After cleaning, iron with steam over an old cloth to remove any residue from the steam vents. 2-WAY STEAM CLEAN™ SYSTEM are trademarks of General Magnaplate Corp.
This is normal. It is not necessary to completely empty the reservoir. 5. Plug the iron in. Sit it on its heel rest, move the Lever to the DRY position, and turn the dial to 7 to dry the iron out. Allow to shut off automatically.
Need Help? IRON WON'T HEAT? 1. Is the iron plugged in? Is the Power Light on? Press the ON/OFF button. 2. If the light does not come on, will a lamp plugged into the outlet turn on? IRON WON'T START STEAMING? 1.