Programmed Order Playback; Repeat Play - Tascam CD-RW2000 Owner's Manual

3 – Playback operations—Programmed order playback
NOTE
Selecting the playback mode is only possible using
the remote control unit. It is not possible to select the
playback mode using the main unit alone.
1 Press the
PLAY MODE
cycle the display through the following:
• (see 3.2, "Programmed order play-
back" below). The red
PROGRAM
lights in this mode.
• (random track order). In this mode,
each track is played once before the disc repeats.
Using the track search functions will move back-
wards or forwards through the random order, e.g. if
track 7 is followed by track 10, it is possible to use
the track search keys to go back to track 7, which is
remembered as being before immediately before
track 10. The red
SHUFFLE
in this mode.
• . Normal playback mode. Pro-
gramming is cancelled, and playback continues in
the normal order.
The selected mode is shown in large characters and
disappears from the display a few seconds after
selecting the mode, when the display returns to its
previous mode.

3.2 Programmed order playback

The steps to set up to 25 program steps (tracks) to be
played back in a specified order are as follows:
1 Press the
PLAY MODE
shows .
2 The display changes to show
,
meaning that no program steps have yet had
tracks assigned to them.
3 Use the number keys to enter a track number
(including the key to enter values greater
+10
than 9, as described in 3.1.2, "Track search").
There is no need to press
The track entered is assigned to the program
step, and the display changes, showing the
track number, the total time of the program so
far, and the step number, e.g.
.
4 The next program step can then be entered.
NOTE
Steps 3 and 4 above can be carried out from the
main unit by turning and pushing the MULTI DIAL
B
control .
16
TASCAM CD-RW2000
A
key repeatedly to
display indicator
display indicator lights
A
key until the display
ENTER .
5 Repeat steps 3 and 4 above until the program is
complete.
H
6 Press the
PLAY key (
at the first program step.
The display shows the track, the current time
display, and the program step number.
While in programmed playback mode, using
H
the keys or the
SKIP
moves backwards and forwards in the order
set in the program.
I
Use the PAUSE key ( or
porarily or the key (
STOP
of the program.
If the STOP key is used, when playback is restarted,
it starts from the first program step.
Clear the program by pressing
the display shows
also cleared when the disc tray is opened, and if the
key is pressed when playback is stopped in
STOP
programmed order mode.
The programmed play order is not memorized when
power is turned off.
If an attempt is made to enter more than 25 program
steps, the message
the display.

3.3 Repeat play

The unit can repeat the whole of the disc (or pro-
gram) or the current track only.
NOTE
Selecting the repeat mode is only possible using the
remote control unit. It is not possible to select the
repeat mode using the main unit alone.
1 The unit should be in playback, pause or stop
mode.
2 Continue to press the
the display shows
indicator lights) to repeat one track, or
(the
lights) to repeat the whole disc or program.
3 If playback has not started, restart it.
To cancel repeat mode, press the
the display shows
indicator goes out.
REPEAT
L
or ) to start playback
B
control
MULTI DIAL
J
) to halt playback tem-
G I
or ) to stop playback
A
until
PLAY MODE
. The program is
appears on
4
key so that
REPEAT
(the
REPEAT 1
indicator
REPEAT ALL
key so that
REPEAT
and the