Related Manuals for Planet ICA-110
Summary of Contents for Planet ICA-110
-
Page 1: Table Of Contents
Table of Contents Requirements Physical Installation ICA-110 ICA-110W ICA-100PE ICA-100C Configuration Preparation Connecting to the Internet Camera Home Page System Camera Uility IPView Pro operation Launch IPView Pro Search Camera Add Camera View Camera Quick reference in CD-ROM guide... - Page 2 This page is intentionally left blank...
-
Page 3: Requirements
ICA-110 1. Connect an Ethernet cable Connect one end of an Ethernet cable to the LAN port located on the ICA-110 rear panel and attach the other end to the network device (hub or switch). 2. Attach the external power supply Connect the provided power adapter to the ICA-110's connector labeled “5VDC”... -
Page 4: Ica-110
Physical Installation of ICA-110 ICA-110W 1. Attach Wireless Antenna Screw the external antenna provided into the antenna connector located on ICA-110W's rear panel. 2. Connect an Ethernet cable Connect one end of an Ethernet cable to the LAN port located on the ICA-110W's rear panel and attach the other end to the network device (hub or switch). -
Page 5: Ica-100Pe
ICA-100PE 1. Connect an Ethernet cable Connect one end of an Ethernet cable to the LAN port located on the ICA-100PE rear panel and attach the other end to the network device (hub or switch). 2. Power over Ethernet IEEE 802.3 af Simply connect the Ethernet cable, no power adapter needed. -
Page 6: Configuration
3. Check the LEDs The PWR and ACT LEDs should be on. Physical Installation of ICA-100C-V2 Configuration The Internet Camera contains an HTTP server. This enables you to connect and configure it using your Web Browser. Preparation Before attempting to connect the Internet Camera, please ensure that: •... -
Page 7: Home Page
2. Start WEB browser on one of the PCs in the same LAN segment. 3. In the Address box, enter “http://” and the IP Address of the Internet Cam- era, as in this example, which uses the Internet Camera’s default IP Address: http://192.168.0.20 If you have difficulties on entering the web interface by the default IP address, press Internet Camera’s reset button continuously for three... - Page 8 ICA-100C-V2 configuration...
- Page 9 ICA-110W configuration IP Assignment: There are some options to select from the IP Assignment. Access to Internet Camera is done through assigning a proper IP address. Please make sure to use a vacant IP address when you assign Note: the IP address for Internet Camera.
- Page 10 Manually Assign / Static IP Address Directly enter the IP address according to local network environment. The default settings are as follows: • Default IP – 192.168.0.20 • Subnet Mask – 255.255.255.0 • Default Gateway – 0.0.0.0 Assign Automatically Using If your network is using DHCP server you can click on “DHCP”.
-
Page 11: Camera Uility Ipview Pro Operation
Wireless Channel: The pull down menu provides the wireless channel for commu-nication. A “channel” is a range of frequencies to be used in communication between ICA-110W and Access Point in infra-structure mode or ICA-110W and PC/Notebook in Ad-hoc mode. Select the appropriate channel from the list provided depending on the regulatory region that the unit is sold. - Page 12 STEP 2 To install the IPView Pro Application click on the “IPView Pro” hyperlink to activate the installation procedure for the application program. If the above screen is not shown, you can start the installation as follows. 1. Click on Start Menu/ Run. 2.
- Page 13 STEP 3 The Welcome screen will appear. Click on the "Next" button to proceed with the installation. STEP 4 The License Agreement prompt will appear as below. Read the details carefully and click on the "Yes" icon to continue with the installation procedure.
- Page 14 STEP 5 A prompt will appear and in the Destination Location dialog box, you may click on "Next" to accept the recommended destination location or click on "Browse" to select another location. After specifying the desired destination location, click on "Next" to proceed further.
- Page 15 STEP 7 Please wait until one of the following two dialog boxes to appear. If the system has to restart, select "Yes, I want to restart my computer now" and click the Finish button to complete the installation procedure. Otherwise, you may simply click the Finish button to complete the installation procedure.
-
Page 16: Launch Ipview Pro
Launch IPView Pro After successfully installing the IPView Pro, the application program is automatically installed to \Program Files\IPView Pro. Click on Start > Programs > PLANET> IPView Pro > IPView Pro to launch the program. Once IPView Pro is launched, the following main screen will appear. -
Page 17: Add Camera
Add Camera Once the available cameras are displayed in the Add Camera column, then select a camera and press Add Camera button. After adding the camera, the camera name will be displayed in the Camera List column as following picture:... -
Page 18: View Camera
View Camera Press save button to save the configuration. Then press the configuration button again to close the configuration window in order to go back the main screen. Now user can view the video image as following picture:... -
Page 19: Quick Reference In Cd-Rom Guide
Quick reference in CD-ROM guide This guide is used to help you startup your Internet camera. It is also recommended to check the CD-ROM manual for more detail information, and product features. - Page 20 This page is intentionally left blank...
Need help?
Do you have a question about the ICA-110 and is the answer not in the manual?
Questions and answers