Tannoy CMS801 DC BM Installation Manual

Tannoy CMS801 DC BM Installation Manual

Ceiling monitor systems
Hide thumbs Also See for CMS801 DC BM:

Advertisement

CMS
C E I L I N G M O N I T O R S Y S T E M S
I N S T A L L A T I O N
M A N U A L
CMS801 DC BM
CMS801 DC PI
CMS801 sub BM
CMS801 sub PI
CMS801 PI back can
Tannoy has a policy of continuous improvement and this specification sheet provides the latest information at the time of printing.
All specifications may be subject to further change. Please contact the Tannoy website for the latest information.
CMS
CMS801 TEMPLATE HOLE CUTOUT SIZE: 295mm (11.61")

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CMS801 DC BM and is the answer not in the manual?

Questions and answers

Summary of Contents for Tannoy CMS801 DC BM

  • Page 1 CMS801 PI back can Tannoy has a policy of continuous improvement and this specification sheet provides the latest information at the time of printing. All specifications may be subject to further change. Please contact the Tannoy website for the latest information.
  • Page 2: Table Of Contents

    When using a power driver to install the product it is essential to use the correct torque level settings to avoid over tightening and damage to the ceiling material or clamps. Recommended torque setting: 1.5Nm Tannoy will not be held responsible for any damages caused by the improper installation of these loudspeakers. ELECTRICAL SAFTEY NOTICE: To comply with the standard UL1480, metal - clad flexible conduit (BX) is required for connection to the terminal block for proper earth grounding.
  • Page 3: Product Feature Identification

    4. PRODUCT FEATURE IDENTIFICATION: Conduit/Cable Clamp Tuning Port Euro Type Connector Mounting Wings Fig 1.1: The blind-mount (BM) models come with a pre-fitted back can Screws for Tuning Port mounting wings Rotary Switch Fig 1.2: A pre-install (PI) model shown without optional pre-install back can Euro Type Plug Conduit Knock-out points Fig 1.3: Optional pre-install (PI) back can for PI models...
  • Page 4: Mechanical Installation Guide For Suspended Ceilings

    Slide the speaker assembly through the hole and turn the screws on the front of the speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved. If using a power driver, Tannoy recommends a torque setting of 1.5Nm. DO NOT OVERTIGHTEN! Slide the tile panel back into the suspended ceiling.
  • Page 5: Mechanical Installation Instructions For Optional Plaster Ring

    5.3 MECHANICAL INSTALLATION INSTRUCTIONS FOR OPTIONAL PLASTER RING: An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly constructed, non-suspended ceilings. Nail or screw the plaster ring to the joists. Lay the speaker wiring to where the speaker will be fitted and complete the plastering work on the ceiling.
  • Page 6: Wiring And Setting Up

    All CMS801 models use a 60W transformer. When using distributed-line systems, the transformer can be tapped at 60W, 30W and 15W, with an additional 7.5W tapping for 70.7V line systems. 7.1 CMS801 DC BM DIMENSIONS: TEMPLATE HOLE CUTOUT SIZE: 295mm 327.8 310.5...
  • Page 7: Cms801 Sub Pi Dimensions

    7.4 CMS801 sub PI DIMENSIONS: TEMPLATE HOLE CUTOUT SIZE: 295mm 117.5 [4.63"] 18.5 [0.73"] 325.0 [12.80"] 7.3 CMS801 PI BACK CAN DIMENSIONS: TEMPLATE HOLE CUTOUT SIZE: 295mm 291.4 397.0 [11.47"] [15.63"] [0.35"] 8.1 TECHNICAL SPECIFICATIONS: MODEL System Frequency response (-3dB) BM back can Frequency range (-10dB) BM back can...
  • Page 8: Painting

    UL-1480, UL-2043, CE (pending) number has been altered or removed. Work under warranty should only be carried out by a Tannoy Professional dealer or service agent. This warranty in no way affects your statutory rights. For further information please 295mm (11.61") contact your dealer or distributor in your country.
  • Page 9: Declaration Of Conformity

    11. DECLARATION OF CONFORMITY: The following apparatus is manufactured in China for Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed...
  • Page 10 NOTES NOTES...

This manual is also suitable for:

Cms801 dc piCms801 pi back scanCms801 sub bmCms801 pi back canCms 801 bm sub

Table of Contents