Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tannoy I6 AW ICT
Summary of Contents for Tannoy I6 AW ICT
-
Page 1: User Manual
AW ICT & i6T AW ICT USER MANUAL... -
Page 2: Table Of Contents
CONTENTS 1. Introduction 2. Unpacking 3. Connectors/Cabling 4. Polarity Checking 5. Amplification & Power Handling 6. Power Selection 7. Equalisation 8. Dimensions 9. Hardware 10. Performance Data 11. Technical Specifications 12. Troubleshooting Guide 13. i6 Recommended Service Parts & Accessories 14. -
Page 3: Introduction
Available in black or white the i6 AW ICT will effectively blend into most backgrounds. Utilisation of the point source ICT Drive unit allows the i6 AW ICT to be mounted on a wall or ceiling in either horizontal or vertical orientations without affecting its performance. -
Page 4: Polarity Checking
CABLE RUN C.S.A. OF EACH CONDUCTOR (mm) 4. Polarity Checking It is most important to check the polarity of the wiring. A simple method of doing this without a pulse based polarity checker for LF units is as follows: Connect two wires to the +ve and -ve terminals of a PP3 battery. -
Page 5: Equalisation
loudspeaker. When the relevant tappings have been selected add the individual wattages required at all speakers and select an amplifier with a rating equal to or exceeding the total wattage required. All of the transformer primaries should be connected in parallel to the output of this amplifier. If for example, you select the 30- watt transformer tap, it means that at full rated amplifier output the speaker will receive the full 30 watts. -
Page 6: Hardware
9. Hardware The i6AW ICT can be wall or ceiling mounted using the MB6 (optional) bracket (fig 1.) which is designed to offer the maximum flexibility in selecting the desired angles. The MB6 is supplied with M8 bolts for fixing to the loudspeaker (fig1.& 2). After fixing the bracket to the wall or ceiling remove the plastic plugs from the top and bottom of the loudspeaker. -
Page 7: Performance Data
10. Performance Data Anechoic Frequency Response, 1watt @ 1m Impedance... -
Page 8: Technical Specifications
11. Technical Specifications Frequency response (1) +/- 3dB Recommended Amplifier Power Power Handling Sensitivity (1) 2.83 volt @ 1m Maximum SPL (3) @ 1m Transformer (i6T AW ICT) Impedance Driver Complement Crossover Point Enclosure Finish Protective Grille Connectors Fittings Dimensions Weight Shipping Dimensions NOTES:... -
Page 9: Troubleshooting Guide
12. Troubleshooting Guide Symptom No Output From Speakers Intermittent Output Poor Low Frequency Output Irregular sounds such as buzzing and humming emanating from the loudspeaker Possible Cause Broken Speaker Cables(s) Amplifier Poor Connection “Out of phase” connection Poor system grounding Faulty electronic device in the signal chain Action... -
Page 10: Warranty
7900 0593 14. Warranty No maintenance of the i6 AW ICT loudspeaker is necessary. All Tannoy professional loudspeaker products are covered by a 5 year warranty from the date of manufacture subject to the absence of misuse, overload or accidental damage. -
Page 11: Declaration Of Conformity
Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to operate as intended, and, the apparatus has an adequate level of intrinsic immunity... - Page 12 Tannoy Loudspeakers are manufactured in Great Britain by : Tannoy Ltd, Rosehall Industrial Estate, Coatbridge, Strathclyde, ML5 4TF, SCOTLAND Telephone: +44 (0)1236 420199 Fax: +44 (0)1236 428230 Tannoy North America Inc, Suite 1. 335 Gage Avenue, Kitchener, Ontario, CANADA, N2M 5E1 Telephone: (519) 745 1158 Fax: (519) 745 2364 Issue 1.0 Part No.