Command access MLB51 Installation Instructions

Installation Instructions
MLB51/53/54
Baldwin Lock modified by Command Access Technologies
STEP 1: The door must be machined with a 3/8" wire raceway,
mortise lock pocket & prepped for a energy transfer
hinge. Make sure the mortise pocket is free of debris.
Mortise
Mortise
Lock Mortise
Lock
Lock
Pocket
Pocket
Mortise
Pocket
Lock
Pocket
3/8 Wire Raceway 3/8 Wire Raceway
3/8 Wire Raceway
3/8 Wire Raceway
3/8 Wire Raceway
STEP 2: Run the wires from the ETH hinge through the 3/8"
raceway starting at the ETH hinge & exiting into the
mortise pocket.
Mortise
Mortise
Mortise
Mortise
Lock Lock
Lock
Lock
Pocket Pocket
Pocket
Mortise
Pocket
Lock
Pocket
3/8 Wire Raceway 3/8 Wire Raceway
3/8 Wire Raceway
3/8 Wire Raceway
3/8 Wire Raceway
STEP 3: Screw the ETH hinge to the door. At this time DO NOT
connect the hinge wires on the jamb side to the wires
coming from the power supply.
EU: (Fail Secure) When power is applied, the outside trim will unlock. When
power is removed, the outside trim is locked.
EL: (Fail Safe) When power is applied, the outside trim will lock. When
power is removed, the outside trim is unlocked.
REX: (Request to Exit Switch) Monitors the inside handle.
LBM: (Latchbolt Monitor Switch) Monitors the position of latchbolt.
EU (Fail Secure) EU (Fail Secure)
EU (Fail Secure)
EU (Fail Secure)
EU (Fail Secure)
Bridge Rectifier Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
EL (Fail Safe) EL (Fail Safe)
EL (Fail Safe)
EL (Fail Safe)
EL (Fail Safe)
Bridge Rectifier Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Bridge Rectifier
Command Access Technologies | 22901 La Palma Ave. Yorba Linda, CA 92831 | Phone: (888) 622-2377 | www.CommandAccess.com
Command Access Technologies is not a licencee, affiliated, associated or connected with Baldwin or any of their subsidiaries or affiliates.
Mortise
Lock
Pocket
ETH Hinge Pocket ETH Hinge Pocket
ETH Hinge Pocket
ETH Hinge Pocket
ETH Hinge Pocket
Wire Transfer Hinge Wire Transfer Hinge
Wire Transfer Hinge
Wire Transfer Hinge
Wire Transfer Hinge
LEGEND OF TERMS
Switch
EU (Fail Secure) Switch
EU (Fail Secure)
Energy Transfer Hinge Energy Transfer Hinge
EU (Fail Secure)
Energy Transfer Hinge
Energy Transfer Hinge
EU (Fail Secure)
Energy Transfer Hinge
Switch
EL (Fail Safe) Switch
EL (Fail Safe)
Energy Transfer Hinge Energy Transfer Hinge EL (Fail Safe)
Energy Transfer Hinge
Energy Transfer Hinge
EL (Fail Safe)
Energy Transfer Hinge
STEP 4: Connect the wires exiting the mortise pocket to the
Bridge Rectifier (included).
STEP 5: Connect the Bridge Rectifier to the plug exiting the
mortise chassis.
STEP 6: Carefully slip the connected mortise lock chassis into the
mortise pocket paying close attention not to pinch any
wires.
STEP 7: Mount the chassis per manufacturer's instructions.
STEP 8: Connect the wires from the power supply at the ETH
hinge on the jamb side. Connect the hinge to the jamb.
12VAC/DC 12VAC/DC
12VAC/DC
12VAC/DC
or or
or
or
Switch 24VAC/DC 12VAC/DC 24VAC/DC
Switch 24VAC/DC
EU (Fail Secure) 24VAC/DC
or
Switch 24VAC/DC
Power
Power
Power
Power
Supply Supply
Supply
Supply
Power
Supply
12VAC/DC 12VAC/DC
12VAC/DC
12VAC/DC
or or
or
or
Switch 24VAC/DC 12VAC/DC 24VAC/DC
Switch 24VAC/DC
EL (Fail Safe) 24VAC/DC
or
Switch 24VAC/DC
Power
Power
Power
Power
Supply Supply
Supply
Supply
Power
Supply
Mortise Mortise
Mortise
Lock Mortise Lock
Lock
Lock Pocket
Pocket
Bridge Bridge Pocket
Bridge
Mortise
Pocket
Bridge
Rectifier Rectifier
Rectifier
Lock
Rectifier
Pocket
Bridge
Rectifier
Mortise
Mortise
Lock
Lock
Bridge Bridge Pocket
Bridge
Rectifier Bridge Rectifier Pocket
Rectifier
Rectifier
Bridge
Rectifier
Plug Plug
Plug
Plug
Plug
ELECTRICAL SPECIFICATIONS
SOLENOIDS:
CURRENT COIL RESISTANCE
VOLTS
350mA 69 Ohms +/- 10%
24VAC/DC
700mA 18 Ohms +/- 10%
12VAC/DC
SWITCHES: 5A 124VAC/DC
REX: Green - Common (C)
Blue - Normally Open (NO)
Gray - Normally Closed (NC)
LBM:
Green/Black - Common (C)
Blue/Black - Normally Open (NO)
Gray/Black - Normally Closed (NC)
Mortise
Mortise
Lock
Lock
Pocket
Pocket
Mortise
Lock
Pocket