Summary of Contents for Britax Steelcraft STROLL LITE LX5012 Series
Page 1
STROLL LITE LAYBACK STROLLER IMPORTANT: KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE www.britax.com.au Series LX5012...
Page 2
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE STROLLER. • DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR USE WITH THIS STROLLER BY BRITAX. • IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH THIS STROLLER.
• DO NOT HANG BAGS UNLESS THEY ARE SUPPLIED OR GOODS FROM THE HANDLE AS THIS COULD CAUSE THE STROLLER TO TIP OVER. • DO NOT LEAVE THE STROLLER AND ITS ACCESSORIES NEAR AN OPEN FIRE OR EXPOSED FLAME. • DO NOT PLACE MORE THAN 6 KG IN THE BASKET. www.britax.com.au...
• Change direction by turning your feet and not your back. • To set the load down, squat down, keep your head up and • Let your legs do the work. Remember to ‘THINK TALL ’ chest lifted, shoulders relaxed, chin tucked in and head level. www.britax.com.au...
PARTS LIST 1x Stroller Frame & Basket 2x Front Wheels 2x Rear Wheels www.britax.com.au...
Page 6
TO UNFOLD THE STROLLER. OPENING THE STROLLER FRAME Make sure the carry Release on the frame Open the frame by strap is out of the lock and open the lifting the handle. way and hangs freely frame. before opening the stroller frame. www.britax.com.au...
Fig.1 at the top of the plastic housing as figure 1. Push down the handle to make sure the stroller frame is fully opened and locked. If not please repeat the steps D and E. Fig.2 Fig.3 www.britax.com.au...
To attach the front wheels, insert To remove the front wheels, press each wheel into wheel housing the quick release button on the top and push in until locks. Pull on the of the front leg mouldings. wheel to ensure it is locked. www.britax.com.au...
ENSURE THAT THE SHOULDER STRAPS ARE FITTED THROUGH THE APPROPRIATE HARNESS SLOTS TO SUIT YOUR CHILD’S SEATED SHOULDER HEIGHT. Slide the shoulder harness pads onto the shoulder harness straps and adjust to the position which fits comfortably on the child. www.britax.com.au...
Page 10
To lock the front wheels into the fixed To allow the wheels to swivel, push position, press the swivel lock up the swivel wheel lock down on both on both wheels until they lock into wheels until they swivel freely. position. www.britax.com.au...
Page 12
Position the shoulder strap tongue Push both buckle tongues (A + (A) on top of the waist buckle B) into the buckle housing (C) tongue (B) on both sides. until the buckle tongues lock into position. www.britax.com.au...
3 bar slider up or down to adjust to the desired fit. Always adjust the harness strap when changing the seating position of the child. CAUTION: DO NOT SLIDE 3 BAR SLIDER OVER THE SEWN TAB ON SHOULDER HARNESS. www.britax.com.au...
To change the shoulder harness Select the appropriate shoulder height, push the shoulder harness harness height and pull each tongue out of the current harness shoulder harness tongue through slot and through the back of the seat. the harness slot. www.britax.com.au...
Page 15
A wrist tether strap is provided on the handle grip. Slide your hand through the tether strap loop whenever you use the stroller. Only remove your hand from the tether strap loop when the brakes have been applied to the stroller wheels. www.britax.com.au...
• Do not run with the stroller. • Whenever you stop, always apply the brakes before you leave the stroller. • Do not hang bags or goods unless it is supplied from the handle. Use the storage basket. www.britax.com.au...
Page 17
PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS. • THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE INJURED WHEN THE STROLLER IS BEING FOLDED, DUE CARE SHOULD BE EXERCISED. • KEEP CHILDREN CLEAR OF THE STROLLER DURING FOLDING THE STROLLER. www.britax.com.au...
Lift the carry strap Folding lock will be upward quickly to fold automatically engaged the stroller. when the stroller is fully folded. Ensure the lock is engaged completely. www.britax.com.au...
- tighten if required. To maintain the safety of your nursery product, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by Steelcraft. THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. www.britax.com.au...
Page 20
CUSTOMER SERVICE 1300 303 330 - Australia 0508 688 822 - New Zealand Due to our continuing program of development, Britax reserves the right to alter the specifications, color or design without any further notice. The Steelcraft trademark is the property of Britax Childcare Pty.Ltd - Australia.