Table of Contents
Advertisement
Operation Manual
DIESEL ENGINE
ARTICLE 92454
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH
Seite 1
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Advertisement
Table of Contents
Related Manuals for WilTec C173F
Summary of Contents for WilTec C173F
- Page 1 Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 1 http://www.WilTec.de http://www.aoyue.eu...
- Page 2 The information contained in this document is subject to change without prior notice. No part of this document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram.
-
Page 3: Refueling Precautions
Keep the engine at least 3 feet(1 meter) away from build- ings or other structures. Keep the engine away from flammables and other haz- ardous materials(trash, rags, lubricants, explosives). © by WilTec Wildanger Technik GmbH Seite 3 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... -
Page 4: Protective Cover
Wear snug fitting working clothes when operating the en- gine. Loose aprons, towels, belt, etc., may be caught in the en- gine or driving train causing a dangerous situation. © by WilTec Wildanger Technik GmbH Seite 4 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... -
Page 5: Technical Parameters
TECHNICAL PARAMETERS © by WilTec Wildanger Technik GmbH Seite 5 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... -
Page 6: Overall Dimensions
If the belt is fixed too tight, the engine will be overloaded while starting, the belt will be drawn longer, and the engine may be damaged. If the belt is fixed too loose, the belt will slip at high speed and high load. © by WilTec Wildanger Technik GmbH Seite 6 http://www.WilTec.de http://www.aoyue.eu... - Page 7 Note: the value of L is shown in figure below. Please contact us or dealer if you have any questions. TILT The tilt must be kept within the allowed value shown: Output shaft tilt Allowed tilt (continuous running) Engine tilt Allowed tilt (continuous running) © by WilTec Wildanger Technik GmbH Seite 7 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 8: Connection Dimensions
CONNECTION DIMENSIONS SIZES OF OUTPUT SHAFT MODEL SPLINE SHAFT TAPER SHAFT SIZES OF PTO FLANGES © by WilTec Wildanger Technik GmbH Seite 8 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 9 DESCRIPTION OF DIESEL ENGINE PARTS OPTIMAL ENGINE SETTINGS VALVE OPEN AND CLOSE PHASE (UNIT: CA) FUEL SUPPLY ADVANCE ANGLE (UNIT: CA) VALVE CLEARANCE (UNIT: mm) © by WilTec Wildanger Technik GmbH Seite 9 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 10 New engine or newly maintained one must be run at low speed and low load at first 20 hours. Do not allow to run it at high speed and full load. © by WilTec Wildanger Technik GmbH Seite 10 http://www.WilTec.de http://www.aoyue.eu...
- Page 11 CHOICE OF FUEL, LUBRICANT AND PREPARATION BEFORE START © by WilTec Wildanger Technik GmbH Seite 11 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 12 Avoid overload within the first 20 working hours. If it is overloaded, its life span will be shortened. Change the machine oil regularly. © by WilTec Wildanger Technik GmbH Seite 12 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 13: Starting The Diesel Engine
STARTING THE DIESEL ENGINE RECOIL START NOTE: WHEN THE ENGINE IS RUNNING, DO NOT PULL THE RECOIL HANDLE OTHERWISE THE ENGINE MAY BE DAMAGED. © by WilTec Wildanger Technik GmbH Seite 13 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 14 © by WilTec Wildanger Technik GmbH Seite 14 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 15 If the liquid in the accumulator is not enough, the electric motor will not run for too little electric current. So, keep the liquid level between upper and low limit marks. The liquid will splash on near parts (which will be spoiled) if it is too much in the accumulator. © by WilTec Wildanger Technik GmbH Seite 15 http://www.WilTec.de http://www.aoyue.eu...
-
Page 16: Running The Engine
3) Which color has the exhaust gas? Is it black as usual or too white? If any of above phenomena is detected, stop the engine immediately and contact our local dealer. © by WilTec Wildanger Technik GmbH Seite 16 http://www.WilTec.de http://www.aoyue.eu... -
Page 17: Stopping The Engine
NOTE: Only after stopping the engine you can pull the recoil handle, otherwise the engine may be damaged. © by WilTec Wildanger Technik GmbH Seite 17 http://www.WilTec.de http://www.aoyue.eu... -
Page 18: Technical Maintenance
(First time) Grind valve holder of inlet and exhaust Change piston ring Check accumulator liquid Every month Clean the core of air filter (Clean) every month or 50 hours © by WilTec Wildanger Technik GmbH Seite 18 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 19 The core of filter obstruction means that the air in combustion chamber will decrease, and the output of engine decreases, and consumption of fuel and lubricant increases. It is also difficult to start the en - gine. Clean the core of filter regularly. © by WilTec Wildanger Technik GmbH Seite 19 http://www.WilTec.de http://www.aoyue.eu...
- Page 20 (that is at the point of compression stroke, where the intake and exhaust valves are closed, which can prevent engine from rust). 6) Clean out machine oil and dirt from the engine, and to put the engine at a dry place. © by WilTec Wildanger Technik GmbH Seite 20 http://www.WilTec.de http://www.aoyue.eu...
-
Page 21: Troubleshooting
Grind the gas valves, if the vestige is too deep, please send it to factory for remedy. The valve stem is clipped on Disassemble the gas valve and clean the stem and guide pipe. guide pipe. © by WilTec Wildanger Technik GmbH Seite 21 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 22 Check the injection pressure and spray condition and correct it. Or change the nozzle if it is damaged. Air is not enough or leaky. Clean the air filter, check the cause of leakage and remedy. © by WilTec Wildanger Technik GmbH Seite 22 http://www.WilTec.de http://www.aoyue.eu...
-
Page 23: Other Possible Problems
Exhaust with black smoke sud- Check fuel system, especially nozzle. denly. There is metal knocking sound The fuel delivery angle is too big. Adjust it. rhythmically in the cylinder. WIRING DIAGRAM © by WilTec Wildanger Technik GmbH Seite 23 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 24 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.