Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ISE RISE
Summary of Contents for ISE RISE
- Page 1 RISE Assembly Instructions UPDATED July 1, 2013...
-
Page 2: Part List
54006700 [xx] - 44” - 75” or Height Adjustable Leg Kneesaver Z-Bar 68002513 [xx] - 76” - 90” 2 pcs. 2 pcs. Adjustable Bar 1 pc. RISE - Glide 68002505 [xx] 68001089 Foot Side Support (attached to feet) 4 pcs. 2 pcs. -
Page 3: Tools Required
Fix-Kit- 6 QKA - Tableclip 55750100 Plastic Round Cap Plastic Wire Clip Plastic 12 pcs. 6 pcs. Rectangular End-Cap 4 pcs. 68002462-PS 68002462-PS-CABLE Leg Motor Cable Power Adaptor Power Cable (attached to motors) 1 pc. 1 pc. 2 pcs. Note: The hardware bag may contain extra components. Tools Required: Phillips Screwdriver M5 Hexagonal Wrench... - Page 4 Assembly Instructions: caution - please read notes carefully 1. Attach Feet to Height Adjustable Legs Left Height Adjustable Leg Sub-Assembly Position the 2 Height Adjustable Legs making sure the wire cutouts on the Motor Housings are facing each other. Motor Housing Cutout Using an M5 Hexagonal Wrench attach the Feet to the Height Adjustable Legs with 8 Black M8x16mm Front of Motor Housing...
- Page 5 3. Attach Adjustable Bar to Motor Housings Facing the rear of the Height Adjustable Leg Assemblies, use an M5 Hexagonal Wrench to fasten the Adjustable Bar with the 4 Silver M8x25mm Countersunk bolts onto the rear of the Motor Housings. Make sure to use the 2 outer holes on each end of the Adjustable Bar.
- Page 6 4. Attach the Kneesaver Z-Bars Position the Sub-Assembly upright and face the front. The Adjustable Bar should be in the rear. Loosen the 4 Adjusting Bolts in the middle of the Adjustable Bar while making sure to not change the width alignment performed earlier.
- Page 7 After the Kneesaver Z-Bars have been fastened to the Adjustable Bar, fasten the other ends of the Kneesaver Z-Bars to the front of the Motor Housings using the 4 Silver M8x25mm Countersunk bolts. Install the 2 Rectangular Plastic End-Caps. See Figure 5. Silver M8 x 25mm Rectangular Plastic End-Caps Countersunk Bolts...
- Page 8 NOTE: Ensure motor is properly positioned into the motor housing Ensure motor cable stain relief is positioned in the motor housing cut-out Ensure all motor connectors are properly connected Connectors Strain Relief Motor Motor Housing...
-
Page 9: Installation Instructions
5. Install the Worksurface Place the Worksurface on the oor with the bottom facing up. Make sure to lay it on a protective layer to prevent scratching. Using a tape measure, position the frame so that the distance between the back edge of the Worksurface is 3”... - Page 10 Note: For Digital Readout Memory Switch see seperate instruction guide. 6. Mount the Standard Up/Down Switch Warning: Make sure the Power is disconnected until table is fully assembled Select a convenient location on the underside of the Worksurface such that the Standard Up/Down Switch can be easily accessed.
- Page 11 3. Table is ready to be used. NOTE: It is sometimes necessary to press the DOWN button twice to start the initialization as the system can be in di erent modes when initialization is attempted. Figure 10. Fully Assembled RISE Table...
- Page 12 Side Support Installation Instructions - For bases 30” - 36” only 1. Install the two Side Supports with the four M8x25mm Countersunk Bolts onto the Left and Right Motor Housings of the Rise base. Side Support M8x25mm Countersunk Bolt Figure 11. Installing Side Supports...
Need help?
Do you have a question about the RISE and is the answer not in the manual?
Questions and answers