Reset To The Default Setting (Except For Parental Setting); Information; Troubleshooting Guide - Sylvania DP170SL8 Owner's Manual

Reset to the Default Setting (Except for PARENTAL Setting)

1
Press [SETUP] in the
stop mode.
SETUP
STOP
SETUP menu
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT 4:3 LETTER BOX
PROGRESSIVE OFF
DOLBY DIGITAL BITSTREAM
OK

Troubleshooting Guide

If this unit does not perform properly when operated as instructed in this manual. Refer to the following:
Problem
No power. • Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
This unit does not • Check if the power plug is connected to an AC outlet.
respond to the remote • Check the batteries in the remote control.
control. • Aim the remote control directly at the infrared sensor window. If necessary, remove all the obstacles
• You have to be within 23 feet (7m) of this unit.
• Tune your radio to an empty AM station so that you hear a lot of static. Turn up the volume, then
• Press and hold any button on remote control toward a digital camera. The remote control is working
Poor picture or noise. • Interference signal may be received. Change the position and direction of the unit.
No picture. • Connect the video cable firmly.
• Insert a correct video disc that can be played back on this unit.
• Set "PROGRESSIVE" correctly in "DISPLAY" menu. Turn it on only if your TV has progressive scan and
No image from HDMI • Check the HDMI connection. (Check the status of the HDMI related indications.)
connection. • Check whether the connected monitor device or other device supports HDCP. (This unit will not
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches the supported input format
Distorted picture. • Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunc-
• Although pictures may stop for a moment, this is not a malfunction. Refer to page 11.
• Check if "PROGRESSIVE" mode is set correctly according to your TV. Refer to pages 20-21.
Disc cannot be played • Insert the disc.
back. • Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface.
No sound. • Connect the audio cables firmly.
• Turn on the power of the audio component.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output. • This unit does not support DTS audio.
Audio or subtitle • The selected language is not available for audio or subtitles on the DVD.
language does not match
the setting.
The camera angle cannot • The DVD does not contain sequences recorded from different camera angles.
be changed.
Audio or subtitle • The DVD does not contain audio source or subtitles in the selected language.
language
cannot be changed.
" " appears on the TV • That operation is prohibited by this unit or the disc.
screen, prohibiting an
operation.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this manual for details on correct operations.
• Playback from a desired track and random playback are not available during programmed playback.
• Some functions are prohibited on some discs.
2
Select "INITIALIZE".
ENTER
QUICK SETUP
PLAYER MENU ENGLISH
TV ASPECT 4:3 LETTER BOX
PROGRESSIVE OFF
DOLBY DIGITAL BITSTREAM
OK

INFORMATION

between the sensor and the remote control.
if you hear some signal sound from the radio in response to your pressing buttons on the remote
control, the remote control is working.
if you confirm infrared light through the digital camera.
you are using the component video connections between the unit and the TV. Disable progressive
scan for all other connections. Refer to page 6.
output a video signal unless the other device supports HDCP.)
of other connected device.
tion.
-This is not a malfunction.
-This is not a malfunction.
-This is not a malfunction.
-This is not a malfunction.
-This is not a malfunction.
3
Select "YES".
ENTER
ENTER
INITIALIZE
Initialize?
NO
YES
ENTER
Corrective action
– 25 –
4
To exit the menu
SETUP
ENTER
Press
Note:
twice.
• When you do not wish
to initialize, select
"NO" at step 3.
EN