Starting A Charge Or Discharge Process; Screen Displays During A Process; Displays During Charge And Discharge Processes - ROBBE Power Peak Infinity 3 Operating Instructions Manual

6.1 STARTING A CHARGE OR DISCHARGE PROCESS

Before the selected process can be carried out, you must connect the battery to the
Output 1 charge sockets, taking care to maintain correct polarity. It is important to use
suitable charge leads, e.g. those from the comprehensive robbe range.
[ [ N N I I M M H H ] ] B B A A T T T T E E R R Y Y
C C H H A A R R G G E E
- - - - B B A A T T T T E E R R Y Y
- - - - C C H H E E C C K K - - - -
audible signal alerts you to the error.

7. SCREEN DISPLAYS DURING A PROCESS

7.1 DISPLAYS DURING CHARGE AND DISCHARGE PROCESSES

[ [ N N O O R R M M A A L L ] ] C C H H A A R R G G E E
T T I I M M E E : :
C C A A P P A A C C I I T T Y Y : :
V V O O L L T T A A G G E E : : 1 1 2 2 . . 7 7 4 4 2 2 V V
C C U U R R R R E E N N T T : :
B B A A T T . . T T E E M M P P . . : :
P P E E A A K K . . T T E E M M P P : :
[ [ N N O O R R M M A A L L ] ] C C H H A A R R G G E E
B B A A T T . . T T E E M M P P : :
P P E E A A K K . . T T E E M M P P : :
P P E E A A K K V V O O L L T T : :
A A V V 9 9 : :
I I N N . . V V O O L L T T . . : : 1 1 3 3 . . 1 1 7 7 1 1 V V
B B A A T T T T . . R R E E S S : : 9 9 1 1 m m O O h h m m
[ [ N N O O R R M M A A L L ] ] D D I I S S C C H H A A R R G G E E
T T I I M M E E : : 0 0 : : 1 1 3 3 : : 1 1 8 8
C C A A P P A A C C I I T T Y Y : :
V V O O L L T T A A G G E E : : 1 1 0 0 . . 7 7 6 6 1 1 V V
C C U U R R R R E E N N T T : :
B B A A T T . . T T E E M M P P . . : :
P P E E A A K K . . T T E E M M P P : :
[ [ N N O O R R M M A A L L ] ] D D I I S S C C H H A A R R G G E E
B B A A T T . . T T E E M M P P : :
P P E E A A K K . . T T E E M M P P : :
P P E E A A K K V V O O L L T T : : 1 1 3 3 . . 8 8 4 4 2 2 V V
A A V V 9 9 : : 1 1 0 0 . . 1 1 9 9 2 2 V V
I I N N . . V V O O L L T T . . : : 1 1 3 3 . . 1 1 7 7 1 1 V V
B B A A T T T T . . R R E E S S : : 9 9 1 1 m m O O h h m m
Operating Instructions
POWER PEAK Infinity 3
The selected process is actually started by holding the '3-
D hotkey' pressed in for at least two seconds. The char-
ger emits an audible signal, and checks the connected
battery; at the same time an on-screen message informs
- - - -
you of this. The screen shot printed here shows this pro-
cess. If no battery is connected, the LED flashes, an
appropriate message appears on the screen, and an
Once the selected process has started, the screen swit-
ches to the working display, which shows all the essenti-
0 0 : : 1 1 2 2 : : 1 1 8 8
al values for the process currently in hand; the red Status
2 2 0 0 5 5 m m A A h h
LED also lights up. The screen shot printed here shows a
1 1 . . 0 0 1 1 A A
working display for a charge process in normal mode.
3 3 5 5 . . 3 3 C C
O O
3 3 2 2 , , 5 5 C C
O O
The working display is divided into two screen pages; tur-
ning the '3-D hotkey' clockwise calls up the second page,
3 3 5 5 . . 3 3 O O C C
3 3 2 2 , , 5 5 O O C C
where you can read off the values shown in this screen
1 1 2 2 . . 6 6 5 5 4 4 V V
shot. The displayed value for internal resistance is calcu-
0 0 . . 0 0 0 0 0 0 V V
lated automatically by the POWER PEAK Infinity 3.
The discharge process takes place in a similar way: when
the charger checks the battery, the screen displays the
message 'DISCHARGE'. The screen shots printed here
6 6 5 5 m m A A h h
show the first and second pages of the working display
1 1 . . 0 0 1 1 A A
during a discharge process.
3 3 1 1 . . 5 5 C C
O O
3 3 2 2 , , 5 5 O O C C
Note:
The charge current can be altered while a charge or
3 3 1 1 . . 5 5 O O C C
discharge process is actually in progress, but any change
3 3 2 2 , , 5 5 O O C C
you make at that point only applies to the current process,
i.e. it is not stored.
17
No.
8429